Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
5.
If no key is pressed for 5 seconds, the unit automatically
CHANNEL without save.
EMG2
1.
Using the rotary knob (6)
select
nel. "EMG" must not appears on the display.
2.
Press the AM/FM key (4) to select the modulation mode of the selected
channel.
3.
Long press the EMG key (5).
message says:
.
4.
Turn the rotary knob (6) or use the UP/DN keys (13) on the microphone th
select the priority channel 2. The message says :
5.
Press the PTT switch (12) ou the F key (9) to
BEEP function is activated, a long beep sounds to confirm the success of
the operation (consult then KEY BEEP menu page 46).
6.
If no key is pressed for 5 seconds, the unit automatically
CHANNEL without save.
6) ROTARY KNOB
Turn the ROTARY knob (4) to
adjust
decrease
terclockwise to
the channel.
See § UP/DN BUTTONS ON THE MICROPHONE page 44.
7) USB CHARGING SOCKET
The USB socket (9) can be used to charge smartphones, tablets or other
rechargeable devices with 5 V - 2.1 A.
8) ANL/NB ~ HI-CUT ~ NRC
ANL/NB
(short press)
Short press the ANL/NB key (8) to
The activated filter is shown on the display.
ANL - Automatic Noise Limiter: This filter allows the reduction of background
noises and some reception interferences. In AM mode only.
NB - Noise Blanker: This filter allows the reduction of back ground noise,
and some reception interference.
HI-CUT
(long press)
Long press the HI-CUT key (8) to
appears on the display when the filter is active.
exits
EMERGENCY
a channel other than an emergency chan-
appears on the display, "EMG" blinks. The
.
validate
and exit. IF the KEY
exits
EMERGENCY
channel. Clockwise to increase, coun-
activate/deactivate
the filters in this order:
activate/deactivate
the HI-CUT filter. "HIC"
Hi-Cut: Eliminates high frequency interferences. Has to be used in accord-
ance with the reception conditions.
NRC
This switchable filter improves the receive and transmit mode.
-
Press the F key (9).
appears in the display.
-
Press the NRC key (8) to
activate/deactivate
value other than 0 has been stored (consult the NRC SET menu
If a
or
page 48), otherwise the display indicates
When the NRC is active, "
9) F ~ SKIP ~ MENU
F
(short press)
Allows to
set/validate
functions (see for example § VOX SETTING above).
This key pressed alone don't have any use.
See § FREQUENCY BAND SELECTION page 44.
See § TALKBACK page 45.
SKIP
(long press only if the SCAN function is activated)
skip
This function allows you to
the scan stops on an unwanted channel, press and hold the F key (9) for
1 second to
store
this channel in the SCAN SKIP memory. A beep sounds.
The channel will no longer be scanned. See the § SCAN page 44.
Consult the SCAN SKIP menu page 47 and the RESET menu page 49.
MENU
(short press + long press)
Press F key (9) firs time.
enter
the MENU
See § MENU page 45.
10) VOX ~ VOX SETTING
VOX
(short press)
The VOX function allows
transmitting
phone (or in the optional vox microphone) without pressing the PTT switch
(11). The use of an optional vox microphone connected to the rear panel
disables
of the transceiver (C)
Short press the VOX key (10) in order to
appears on the display. Short press again the VOX key (10) to
function. "VOX" disappears.
43
the NRC.
.
" appears on the display..
a channel found by the SCAN function. When
is displayed. Long press F key (9) second time to
by speaking into the original micro-
the original microphone.
activate
the VOX function. "VOX"
disable
the
Publicidad
Tabla de contenido
