Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Press F key (9).
is displayed.
Long press F key (9) to
enter
the MENU.
OPERATING MODE
1.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
select
to
the
menu.
2.
Briefly press the EMG key (5) to confirm. The operating mode flashes (I d or
DF).
3.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
to
select
the desired operating mode.
STORING A CTCSS/DCS CODE
Depending on the operating mode used, the procedure differs:
Identical mode I d
4.
A short press on the EMG key (5) makes the genre blink ("CTCSS", "DCS" or
"OFF" no genre).
5.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
to
select
the genre or...
6.
Press the EMG key (5) to
confirm
OFF selected).
7.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
select
to
the code (from 01 to 38 for CTCSS and 001 to 104 for DCS).
Different Mode DF
4.
A short press on the MENU key (4) makes the type RX blink.
5.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
to
select
the RX or TX type.
6.
A short press on the EMG key (5)
value flashes ("CTCSS", "DCS" or "OFF" no genre).
7.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
to
select
the genre or...
8.
Press the EMG key (5) to
confirm
OFF has been selected).
9.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
select
to
the code (01 to 38 for CTCSS 001 to 104 for DCS).
10. Press the EMG key (5) to
confirm
5, for set the second type.
11. If you don't need to set the second type, long press the EMG key (5) to
validate
and exit the MENU.
12. If no key is pressed, the device
saving
the changes.
The default mode is I d (Identical). The default genre is OFF.
See the RESET menu.
the genre. The code value flashes (unless
validates
the choice of type. The genre
the genre. The code value flashes (unless
the selected code. The unit return to point
exits
the MENU after 10 seconds without
14) REPEATER / RELAY setting
WARNING! This function is valid only on the D frequency band. See the
configuration table page 74.
This function allows you to
The radio receives on the current channel RX1 and transmits on the selected
channel TX2.
1.
Select the RX1 channel.
2.
Press F key (9).
is displayed.
3.
Long press F key (9) to
enter
4.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
select
to
the
menu.
5.
Short press on the EMG key (5). The current transmission channel RX2 blinks
on the display.
6.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
select
the transmission channel (TX2) or I d (identical, no repeater).
7.
New press on the EMG key (5) to validate. a) Return to the point 1 to set
another menu or b) Short press the F key (9) to
disappears from the display.
8.
If no key is pressed, the unit
from the display.
The default transmission channel is 1d (identical RX channel).
To activate the function, see the § REPEATER/RELAY page 45.
15) RESET
This function allows to
Erase
settings.
Press F key (9).
is displayed.
Long press F key (9) to
enter
1.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
select
the
menu.
2.
Press EMG key (5) to
validate.
49
increase
the range of your CB.
the MENU.
validate
and
exit
exits
MENU after 10 seconds.
the scan skip memory or
restore
the MENU.
The current value blinks on the display.
the MENU.
disappears
all factory
Publicidad
Tabla de contenido
