Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
6) SCAN TYPE
Allows to
select
the TYPE of SCAN.
Press F key (9).
is displayed.
Long press F key (9) to
enter
the MENU.
1.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
select
to
the
menu.
2.
Press EMG key (5) to
validate.
3.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
to
select
the scan type sq or t 1.
4.
Short press the EMG key (5) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (9) to
disappears from the display.
5.
If no key is pressed, the unit
exits
from the display.
"
"means scanning stops when busy channel is founded.
"t 1" means scanning stops when busy channel is founded and return to
scan after 5 seconds.
Type default value is : 59.
7) SCAN SKIP
memorize/erase
This function allows to
memory.
1.
Select a channel
2.
Press F key (9).
is displayed.
3.
Long press F key (9) to
enter
the MENU.
4.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
select
to
the
menu.
5.
Press EMG key (5) to
validate.
6.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
alternate
to
between On and OF.
7.
Short press the EMG key (5) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (9) to
disappears from the display.
8.
If no key is pressed, the unit
exits
from the display.
On memorize the current channel into the SCAN SKIP memory. When a
channel is stored in the memory,
channel number.
OF erase the current channel from the SCAN SKIP memory,
from the display.
The current value blinks on the display.
validate
exit
the MENU.
and
MENU after 10 seconds.
disappears
a channel form the SCAN SKIP
The current value blinks on the display.
validate
exit
the MENU.
and
MENU after 10 seconds.
disappears
appears on the display close to the
disappears
See the § SKIP on page 43.
8) PA SETTING
This function allows to
select
Press F key (9).
is displayed.
Long press F key (9) to
enter
1.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
select
the
menu.
2.
Press EMG key (5) to
validate.
3.
Turn the rotary CH knob (6) or use the UP/DN buttons (13) on the microphone
select
to
the operating mode of the PA : I n, OF or PA.
4.
Short press the EMG key (5) to validate. a) Return to the point 1 to set an-
other menu or b) Short press the F key (9) to
disappears from the display.
5.
If no key is pressed, the unit
from the display.
I n: the modulation of the microphone is transmitted to the external loud-
speaker connected to jack PA.SP. (D). The received signal is transmitted to
the internal loudspeaker [or external optional loudspeaker connected to
jack EXT.SP (E)]. "PA" blinks alternately with the modulation mode (AM or FM).
OF: The reception is no more functional. Only the modulation of the micro-
phone is transmitted to the Public Address loudspeaker connected to jack
PA.SP. (D). PA and le level of the
PA: the modulation of the microphone and the received signal are transmit-
ted to the Public Address loudspeaker connected to jack PA.SP. (D). "PA"
blinks alternately with the modulation mode (AM or FM).
Turn the VOLUME knob (1) to
Default PA setting is I n.
See § PA (Public Address) page 42.
9) MICROPHONE TYPE
PRESIDENT HARRISON II can be used with both a PRESIDENT electret and
dynamic 6-pin microphone (see microphone wiring on page 73). When
the unit is turned on, the microphone type is displayed briefly.
Press F key (9).
is displayed.
Long press F key (9) to
enter
1.
Turn the rotary CH knob (6) or use UP/DN buttons (13) on the microphone
to
select
the
menu.
2.
Press EMG key (5) to
validate.
47
the operating mode of Public Address.
the MENU.
The current value blinks on the display.
validate
and
exit
exits
MENU after 10 seconds.
PA
are displayed.
adjust
the audio level of the mode PA.
the MENU.
The current value blinks on the display.
the MENU.
disappears
Publicidad
Tabla de contenido
