Specified Conditions Of Use; Safety Instructions - Gude UNI MIG 165 SYN Traducción Del Manual De Instrucciones Original

Read and understand the
operating instructions before
using the appliance. Abide by all
the safety measures stated in the service manual. Act
responsibly toward third parties. In case of any doubts
about connection and operation refer please to our
customer center

Specified Conditions Of Use

Welder in protective atmosphere for thermal connec-
tion of ferrous metals by melting edges and including
mixture. Please note that the device is designed for
domestic use only.
Do not use this product in any other way as stated
for normal use. Not observing general regulations
in force and instructions from this manual does not
make the manufacturer liable for damages.
Please note that our equipment has not been
designed for commercial, craft or industrial use. If the
equipment is used in commercial, craft or industrial
operation or for similar activities, we cannot assume
any.

Safety instructions

WARNING! Electric shock! There is a risk of
an injury caused by electric shock!
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
IP21 protection degree of the welder. The welder
must not be exposed to rain and moisture when
being operated or stored.
Check the voltage. Technical data given on the type
label must correspond with electric network voltage.
Insert the plug of the electrical cable in a socket of
suitable shape, voltage and frequency complying
with current regulations.
Use extension cables with a maximum length of 5
meters and with a cable cross-section of not less than
1.5 mm2. Use of extension cables of different length
and cross-section and also of adapters and multiple
sockets should be avoided.
Check the cable and/or socket for damages before
the appliance putting into operation.
Defective cable or plug may cause electric shock.
Do not pull the service cable to pull the plug out of
socket. Do not expose yourself or other persons wit-
hout protection to electric arc or hot metal. Spraying
welding pearls may cause burns. A suitable welding
shield, protective clothes and protective gloves to be
worn at all times.
Long-term inhalation of welding gases may be
harmful to your health. Work with an exhaust system
or in well ventilated spaces. Avoid direct inhalation
of gases.
Contact with the hose bundle nozzle and the material
being processed may cause burns. Special welding
gloves to be worn at all times.
Let the hose bundle nozzle and the material being
processed cool down after being operated.
Long-term working with the appliance may damage
hearing. Hearing protection to be used at all times.
Welder may only be used on a flat surface and with a
properly secured gas bottle.
Make sure the welding smoke is exhausted or the
place of welding ventilated well.
Hot slag and sparks may cause fire or explosion. Never
use the appliance in a flammable environment.
Wood, sawdust, „varnishes", petrol, kerosine, natural
gas, acetylene, propane and similar flammable mate-
rials must be removed from the place of work and the
surrounding area or protected against sparks flying
away. To extinguish fire, a suitable fire extinguisher
must be made ready nearby.
No welding or cutting on closed vessels and pipes.
No welding or cutting on vessels and pipes if they are
open, containing materials able to explode due to
heat or moisture or able to cause other dangerous re-
actions. Never use the welder to defrost frozen pipes.
The gas bottle must necessarily be secured against
falling.The welder must never be lifted together
with the gas bottle. Special regulations apply to the
transport of gas bottles.
Handling of gas bottles
Make sure the gas bottles are used and stored in
rooms with sufficient air inlet and outlet.
A leaking gas bottle may reduce the share of oxygen
in the inhaled air and therefore represent a risk of
suffocation. Before use, make sure the gas bottle
contains gas designed for the work being done.
Gas bottles must always be safely fixed in a vertical
position on a wall support or on a specially manufac-
tured gas bottle cart.
The bottle with shielding gas and the fixed adjust-
ment gas current equipment must not be moved. The
gas bottle valve must be closed during transport.
Close the gas bottle valve after use.
ENGLISH
31