Hopper Assembly - Pit Boss SAVANNAH Manual De Instrucciones

Hopper Assembly

• The hopper includes a pellet clean-out feature to allow for easy
STEP 14
cleaning and the ability to change out wood pellet fuel flavors.
To empty, locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock. Place a
clean, empty pail under the clean-out door and pull the door han-
PELLET CLEAN-OUT FEATURE
The hopper includes a pellet clean-out feature to allow for
easy cleaning and the ability to change out wood pellet fuel dle to open the drop-chute access plate, allowing the pellets from
flavors. To empty, follow these steps:
1. the hopper to empty. Once empty, lift the door handle again to Locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock.
2. unlock. Push the drop-chute access plate back into place. Push the Place a clean, empty pail under the clean-out door and
pull the door handle to open the drop-chute access plate,
allowing the pellets from the hopper to empty.
door handle down to lock closed. (G)
NOTE: Use a long handled brush or shop-vac to remove
excess pellets, sawdust, and debris for a complete cleanout through the hopper screen.
NOTE: Use a long handled brush or shop-vac to remove ex-
3. Once empty, lift the door handle again to unlock. Push
the drop-chute access plate back into place.
cess pellets, sawdust, and debris for a complete clean-out
4. Push the door handle down to lock closed.
through the hopper screen.
• Running all pellets out of your auger system is recommended if
your grill will be unused for an extended period of time. This can
be done by simply running your grill, on an empty hopper, until all
pellets have emptied from the auger tube.
• Check and clean off any debris from the fan air intake vent, found
on the bottom of the hopper. Once the access panel has been re-
moved, carefully wipe off any grease build-up directly on the fan
blades. Use warm soapy water to cut the soot and grease. This
ensures airflow is clean and sufficient to the feed system. (H)
GRILL CARE CHEAT SHEET
ITEM
Bottom of Main Grill
Burn Pot
Cooking Grates
Flame Broiler™
Shelves
Grease Bucket
Auger Feed System
Hopper Electric Components
Air Intake Vent
Grill Probe (Sensor) and Shield
WWW.PITBOSS-GRILLS.COM
STEP 14
PELLET CLEAN-OUT FEATURE
The hopper includes a pellet clean-out feature to allow for
easy cleaning and the ability to change out wood pellet fuel
flavors. To empty, follow these steps:
1. Locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock.
2. Place a clean, empty pail under the clean-out door and
pull the door handle to open the drop-chute access plate,
allowing the pellets from the hopper to empty.
NOTE: Use a long handled brush or shop-vac to remove
excess pellets, sawdust, and debris for a complete cleanout through the hopper screen.
3. Once empty, lift the door handle again to unlock. Push
the drop-chute access plate back into place.
4. Push the door handle down to lock closed.
STEP 14
PELLET CLEAN-OUT FEATURE
The hopper includes a pellet clean-out feature to allow for
easy cleaning and the ability to change out wood pellet fuel
flavors. To empty, follow these steps:
1. Locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock.
2. Place a clean, empty pail under the clean-out door and
pull the door handle to open the drop-chute access plate,
allowing the pellets from the hopper to empty.
NOTE: Use a long handled brush or shop-vac to remove
excess pellets, sawdust, and debris for a complete cleanout through the hopper screen.
3. Once empty, lift the door handle again to unlock. Push
the drop-chute access plate back into place.
4. Push the door handle down to lock closed.
CLEANING FREQUENCY CLEANING METHOD
Every 5-6 Grill Sessions Scoop Out, Wet/Dry Vacuum Out Excess Debris
Every 2-3 Grill Sessions Scoop Out, Wet/Dry Vacuum Out Excess Debris
After Each Grill Session Burn Off Excess, Brass Wire Brush
Every 5-6 Grill Sessions Scrape Main Plate with Slider, Do Not Wash Clean
After Each Grill Session Cloth & Soapy Water
After Each Grill Session Cloth & Soapy Water
When Pellet Bag is Empty Allow Auger to Push Out Sawdust, Leaving
Hopper Empty
Once A Year Dust Out Interior, Wipe Fan Blades with Soapy
Water
Every 5-6 Grill Sessions Dust, Cloth & Soapy Water
Every 2-3 Grill Sessions Cloth & Soapy Water
15
G H
Snapshot this chart
for reference.
PIT BOSS® GRILLS