Publicidad
Idiomas disponibles
Idiomas disponibles
MIN and MAX markings:
There are three markings on the inside of the jug (7).
– The MIN mark shows you the minimum fill quantity.
– The lower MAX mark shows the maximum filling quantity when making milk foam.
– The upper MAX mark shows the maximum filling quantity when heating milk.
4.3 MAKE WARM MILK FROTH
1. Place the whisk (5) as far as it will go on the drive shaft inside the jug (7). Take the jug
(7) from the base (11) and fill with milk at least up to the MIN mark. When frothing, the
volume of the milk increases. To prevent the milk foam from overflowing, only fill the
milk to the lower MAX mark.
2. Put the lid (2) on the jug (7).
3. Place the jug (7) on the base (11).
4. You can make hot milk foam in 2 ways:
- Select operating mode 1 with the on/off switch (9). The symbol for operating
mode 1 (14) flashes and after approx. 3 seconds the whisk (5) starts to turn.
The milk foam is produced.
or
- Select operating mode 2 with the on/off switch (9). The symbol for operating
mode 2 (8) flashes and the whisk (5) starts to turn after about 3 seconds.
The milk foam production starts.
5. As soon as the milk foam is ready, the milk frother switches off automatically, the
symbol of the selected operating mode (14, 8) flashes and goes out after a short
time. You can also stop the preparation prematurely by briefly pressing the button (9).
6. Wait about 30 seconds until liquid milk has settled in the bottom of the jug (7).
7. Lift the jug (7) by the handle (6) from the base (11), remove the lid (2) and use the milk
foam as you wish.
8. After each use, clean the milk frother with tap water to remove any residue.
26
4.4 PRODUCING COLD MILK FOAM
1. Place the whisk (5) as far as it will go on the drive shaft inside the jug (7).
2. Take the jug (7) from the base (11) and fill with milk to at least the MIN mark. When
frothing, the volume of the milk increases. To prevent the milk foam from overflowing,
only fill the milk to the lower MAX mark.
3. Put the lid (2) on the jug (7).
4. Place the jug (7) on the base (11).
5. Select operating mode 4 with the on/off switch (9). The symbol for operating mode 4
(10) flashes and after approx. 3 seconds the whisk (5) starts to rotate. The milk foam
production starts.
6. As soon as the milk foam is ready, the milk frother switches off automatically, the
symbol of the selected operating mode (10) flashes and goes out after a short time.
You can stop the preparation prematurely by briefly pressing the on/off switch (9).
7. Wait about 30 seconds until liquid milk has settled in the bottom of the jug (7).
8. Lift the jug (7) from the base (11), remove the lid (2) and use the milk foam as you wish.
9. After each use, clean the milk frother with tap water to remove any residue.
4.5 HEATING MILK EVENLY
1. Push the whisk (4) onto the drive shaft inside the jug (7) as far as it will go.
2. Take the jug (7) from the base (11) and fill with milk at least up to the MIN mark.
To prevent the heated milk from overflowing, only fill milk up to the upper MAX mark.
3. Put the lid (2) on the jug (7).
4. Place the jug (7) on the base (11).
5. Select operating mode 3 with the on/off switch (9). The symbol for operating mode
3 (13) flashes and after approx. 3 seconds the whisk (4) starts to rotate, ensuring even
heating. As soon as the milk is hot, the milk frother switches off automatically, the
symbol of the selected operating mode (13) flashes and goes out after a short time.
6. Lift the jug (7) from the base (11) by the handle (6), remove the lid (2) and use the
heated milk as you wish.
7. After each use, clean the milk frother with tap water to remove any residues.
27
Publicidad
