Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLATION & OPERATION
4.
HOLD THE PIPE, remove pipe
clamp and slide well seal over rigid
PVC pipe and onto well casing.
Position assembly so that twelve
inches of rigid PVC pipe protrude
from well seal. Alternately turn
bolts on well seal clockwise until
rubber gaskets are tight against
well casing and rigid PVC pipe.
5.
Cement 1-1/4" PVC elbow onto rigid
PVC pipe protruding from well
seal. If desired, some length may
be cut off of rigid PVC pipe before
cementing elbow. Use a round file
or knife to smooth the inside of
any rigid PVC pipe that has been
cut.
6.
Thread a 1-1/4" male PVC adapter
into the front of pump. Hand
tighten, then turn 1/4 turn with
wrench.
STEPS 7–9 ARE FOR THE FP4542 AND FP4562
CONVERTIBLE PUMPS
7.
Open ejector kit
(FP4542 for 1/2 HP;
FP4562 for 1 HP).
Thread shorter venturi
tube into ejector on
top of the nozzle until
snug. Place gasket over venturi tube so that openings in
gasket line up with openings in ejector.
8.
Slide bolts through the bolt openings
on either side of the ejector, through
the gasket and bolt ejector to front of
the pump. Tighten bolts securely.
9.
Thread a 1-1/4" male PVC adapter
into front of ejector. Hand tighten,
then turn 1/4 turn with wrench.
FP1002 (02-01-2023)
10. Cement as many
APPROX.12"
OF PVC PIPE
PROTRUDING
FROM
WELL SEAL
WELL
SEAL
11. Apply 2-3 wraps of PTFE pipe
7128 1016
1-1/4"
PVC
ELBOW
TOP OF
PVC PIPE
PROTRUDING
FROM WELL
12. Prime pump as described in Priming the Pump.
SEAL
13. Apply 2-3 wraps of PTFE pipe
7129 1016
14. Complete all electrical connections as described in Wiring
15. Screw 1" male PVC adapter
16. Thread 10" x 1" nipple into
7158 0117
BOLT
EJECTOR
17. Thread 1/2" boiler drain into
7159 0117
1-1/4"
MALE PVC
ADAPTER
7160 0117
sections and
couplings of PVC
pipe needed to
connect the PVC
elbow to the
1-1/4" male PVC adapter in the front of the pump.
thread sealant tape tape to the
male threads on the discharge
tee. Using pipe wrench, thread
discharge tee into top of pump.
Remove pressure gauge plug
from top of discharge tee.
thread sealant tape tape
to plug and gauge threads.
Thread pressure gauge plug
into discharge tee and thread
pressure gauge into pressure
gauge plug. Make sure all
connections are tightly sealed.
Your Pump.
into discharge tee outlet.
pressure tank. Thread tank
cross into nipple so that the
two 1/4" holes in tank cross
face upward. Plug two outlets
on tank cross with two 1/4"
plugs.
front of tank cross. Thread 1"
male PVC adapter into inlet
side of tank cross. Connect
household plumbing to other
side of tank cross.
1-1/4" PVC PIPE
7127 1016
PRESSURE
GAUGE
PLUG
DISCHARGE
TEE
7161 0117
PRESSURE
GAUGE
7162 0117
1" MALE PVC
ADAPTER
7163 0117
1/4" PLUGS
TANK
NIPPLE
CROSS
7130 1016
1/2"
BOILER
DRAIN
1" MALE
PVC ADAPTER
7131 1016
7
Publicidad
