Carrera RC Green Chopper II Instrucciones De Montaje página 6

Ocultar thumbs Ver también para Green Chopper II:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 11
FCC statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
IC statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Guidelines and warnings for the use of LiPo rechargeable batteries
• You have to charge the attached 3.7 V
battery in a safe place and at a safe distance to flammable material.
• Never leave the battery unattended while it is charging
• After a flight, the rechargeable battery has to cool down to the ambient air
temperature before charging it.
• You must always use the corresponding LiPo charging unit (USB cable /
remote control). In case of non-compliance with these directions there is a
danger of fire resulting in a health risk and/or damage to property. NEVER
use any other battery charger.
• Should the rechargeable battery swell or deform while discharging or recharg-
ing, you have to immediately stop charging or discharging the battery. Take the
battery out as quickly and carefully as possible and place it in a safe and open
area offside any inflammable material and watch it for at least 15 minutes. In
case you continue charging or discharging a battery which has already started
to swell or deform there is a danger of fire! Even in case of slight deforming or
ballooning the rechargeable battery has to be taken out of operation.
• Store the rechargeable battery at ambient temperature in a dry place.
• Always recharge the battery immediately after use to prevent its becom-
ing deep discharged. Please make sure to allow a pause of about 20 min-
utes between finishing the flight and recharging the battery. Recharge
the battery occasionally (suggested every 2-3 months). Failure to treat
the battery as described above can lead to its becoming defective.
• When transporting or temporarily storing the rechargeable battery the tem-
perature should be between 5-50°C. If possible, do not store the battery or
the model in a car and do not expose it to direct sunlight. In case the battery
is broiled it can be damaged or catch fire.
Note: If the battery voltage/output is low you will recognise that a considerable
trim and/or controlling is necessary to avoid that the helicopter starts trundling.
This usually occurs before reaching a battery voltage of 3 V and it is a good
moment to end the flight.
Contents of package
1x Helicopter
1
1x Controller
1x USB charging cable
2x 1.5 V Mignon AA batteries (non-rechargeable)
Recharging the LiPo rechargeable battery
Make sure you only charge the LiPo rechargeable battery supplied with the
LiPo charging unit also supplied (USB cable and remote control). In case you
try to charge the rechargeable battery with a different LiPo battery charger or
any other battery charger, this might cause serious damages. Please carefully
read the previous chapter about warnings and guidelines on the usage of re-
chargeable batteries before proceeding.
Charging via computer:
2
• Connect the USB charging cable with the USB port of a computer. The LED
on the USB charger cable lights green indicating that the charger unit is
correctly connected to the computer. If you plug in a helicopter with a dis-
charged battery, the LED on the USB charging cable does not light up; this
shows that the helicopter battery is being charged. The USB charging cable
and the charging socket on the helicopter are designed to make incorrect
connection impossible.
• It takes about 30 minutes to recharge a discharged battery (but NOT a
deep-discharged one). When the battery is fully charged, the LED display on
the USB charger cable lights up green again.
ENGLISH
150 mAh/ 0,56Wh LiPo rechargeable
Note: When supplied, the lipo-battery is already partially charged so the first
charging cycle may well take less time.
It is essential to follow the connection sequence given above! If you have
the charger cable only connected to the helicopter, and not to a source
of electricity, a green LED display indicates that there is still power in the
battery. The green LED display does not necessarily indicate the battery
is still adequately charged.
While charging, the power switch must be in the "OFF" position.
Inserting the batteries in the remote control
Open the battery compartment with a screwdriver and insert the batteries in
3
the remote control. Please keep in mind the correct polarity. After having
closed the compartment you can check all functions of the remote control with
the help of the power-switch on the front. With the power-switch turned ON and
proper functioning, the top center LED on the remote control will light up red.
When the control LED flashes rapidly, the batteries in the controller must be
changed.
Frequency bind between model and remote control
The Carrera RC helicopter and the remote control are frequency bound at
4
purchase. Should there occur any problems with the communication be-
tween the Carrera RC helicopter and the remote control at the beginning,
please carry out a new frequency bind.
• Switch on the model at the ON/OFF switch.
• The LED in the helicopter now flashes in rhythmically-accelerating sequence.
• Switch on the controller at the power switch. While connecting, the controller
emits a signal tone.
• WARNING! Immediately after switching it on, place the helicopter a flat
and level surface. The gyro-system will then set itself automatically.
• Slide the left joystick, thus the gas lever, completely up and down again into
the zero position.
• Allow the helicopter a few moments until the system is correctly initialised
and is ready for operation.
• The binding has now been successfully established.
• The LED on the controller now lights continuously.
Checklist for flight preparation
This checklist does not replace the contents of the operating instructions. Al-
though it can be used as a quick-start-guide we strongly advise to first read the
operating instructions in detail before you proceed.
• Check the contents of the package
• Connect the charging unit to the source of power.
• Charge the lipo-battery as described in the section "Charging the lipo-battery".
• Fit two AA batteries in the controller, making sure their polarity is correct.
• Look for a suitable environment for flying
• Link as described in
4
.
• Repeat the above points as required, if you wish to fly more helicopters at
the same time.
• Check the control system
• Make yourself familiar with the control system
• Trim the helicopter as necessary as described under "Controlling the helicop-
ter", so that when hovering the helicopter no longer moves from the spot,
until given a command by the controller.
• Press the button
7
to start the helicopter (Figure
• The helicopter is now ready to be flown.
• If the helicopter displays no functions, retry the above binding procedure.
• Fly the model
• Land the model
• Switch the model off at the ON/OFF switch
• Always switch off the remote control last
Range of functions of the remote control
1. Power switch (ON / OFF)
5
2. Control LED
3. Gas
4. Forward/backward · tail (spinning in circles)
5. Trimmer for tail
6. Auto-Landing Button
7. Auto-Start & Fly to 1 m Button
8. Battery compartment
3
6
15 16
).
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Orange sply ii370501027x370501028x

Tabla de contenido