Carrera RC Green Chopper II Instrucciones De Montaje página 7

Ocultar thumbs Ver también para Green Chopper II:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 11
Description of helicopter
1. Coaxial rotor system
6
2. Tail rotor
3. Socket for charging the lipo-battery
4. Landing skids
7
5. ON-/OFF switch
Controlling the helicopter
In case you don´t know the control functions of your Carrera RC helicopter
8
yet, please take some minutes before the first flight in or to make yourself
familiar with them. The descriptions left or right refer to the view out of the
cockpit (pilote´s view). Push the throttle up to increase the rotational speed of
the main rotor blades. Increase the rotational speed of the main rotor blades
and the model will start to ascend.
If you push down the throttle and thus reduce the rotational speed of the main
rotor blades the helicopter will descend. When the model has lifted off the
ground you can get it into stationary hovering without abrupt ascending or de-
scending by carefully moving the throttle upwards and downwards. The right-
hand joystick can be used, without using the left-hand joystick, to fly forwards/
backwards or in a circle at the same flying height.
Move the right lever (tail) to the left and the helicopter's nose turns (yaws)
9
round the main rotor's axis in a circle to the left.
Move the right lever (tail) to the right and the helicopter's nose turns (yaws)
round the main rotor's axis in a circle to the right.
Use the trimmer for tail until you have reached a stable neutral position of the
helicopter when hovering, without moving the right lever (tail).
The forward-/backward lever controls the helicopter´s pitch forward and
10
backward. When shifting the lever forward the nose of the helicopter will
move downwards and the helicopter will fly forward. When shifting the for-
ward-/backward lever backward the helicopter will move backwards and the
helicopter will fly backward.
After having made yourself familiar with the main control functions and having
chosen an appropriate area for flying the helicopter, you can start the first flight.
Choosing the flight area
When being prepared for the first flight you should choose a closed
11
room without any persons or obstacles which is as big as possible.
Due to the size and controllability of the helicopter experienced pilotes may
be able to fly the helicopter in relatively small rooms. For your first flights
we strongly recommend to choose a room with a minimum floor space of 5
x 5 metres and 2.40 metres of height. After having trimmed your helicopter
for flight and having made yourself familiar with the controlling and its
functions you may start flying in smaller and less open environments.
This toy is intended to be used in domestic area (house and garden) only.
Automatic control of altitude
The Helicopter will maintain the current flying altitude automatically as
12
soon as you release the left-hand joystick during the flight. The right-hand
joystick can be used, without using the left-hand joystick, to fly forwards/back-
wards or in a circle at the same flying height.
Auto-Start & Fly to ≈ 1 m
Press the 'Auto-start & fly to ≈1 m' button on the controller, in order to start
13
the motors and automatically fly up to the altitude of about 1 m . You are
able to influence the direction of flight at any time during the starting operation
by means of moving the right joystick. The helicopter will maintain itself in po-
sition automatically as soon as the altitude of about 1 m has been reached.
Auto Landing
You can trigger the automatic landing function at any time by means of
14
pressing the 'Auto landing' button. The speed of the rotors will reduce
gradually as a result. You are able to influence the landing position at any time
during the landing procedure by means of moving the right-hand joystick. The
motor will switch itself off as soon as the helicopter is on the ground.
Trimming the helicopter
Auto-trimming
15
1. Place the helicopter on a horizontal surface.
2. Link the helicopter with the controller as described in "Linking the
model with the controller".
3. Slide the gas lever and the lever for forward / back simultane-
ously into the right lower corner. The LED on the helicopter flashes
on briefly and then lights up continuously. The signalling tone will
sound once.
4. The neutral setting is completed.
When hovering and without you moving the lever for circling on the spot,
16
if the helicopter rotates to left or right, proceed as follows: If the helicopter
rotates quickly or slowly to the left around its own axis, press the trimmer for
rotation below left in steps to the right. If the helicopter rotates to the right,
press the trimmer for rotation in steps to the left.
Troubleshooting
Problem: Remote control does not work.
Cause:
The ON/OFF-power switch is turned "OFF".
Solution: Turn the ON/OFF-power switch "ON".
Cause:
The batteries have been wrongly inserted.
Solution: Check if the batteries have been correctly inserted.
Cause:
The batteries do not have enough power.
Solution: Insert new batteries.
Problem: The helicopter cannot be controlled with the remote control
Cause:
The power switch on the reomote control is turned "OFF".
Solution: First turn the power switch on the remote control "ON".
Cause:
The remote control is possibly not correctly frequency bound with the
receiver on the helicopter.
Solution: Link as described in
Problem: The rotor blades do not rotate.
Cause:
The power switch on the model or the controller is at "OFF"
Solution: Turn the ON/OFF-power switch "ON".
Cause:
The rechargeable battery is too weak or has run out of power.
Solution: Charge the battery (see chapter "Charging the battery").
Problem: The helicopter does not lift.
Cause:
The rotor blades rotate too slowly.
Solution: Push the throttle up.
Cause:
The battery´s power is not sufficient.
Solution: Charge the battery (see chapter "Charging the battery").
Problem: During flight, the helicopter loses speed and height without any
obvious reason.
Cause:
The battery is too weak.
Solution: Charge the battery (see chapter "Charging the battery").
Problem: The helicopter lands too quickly.
Cause:
Loss of throttle control.
Solution: Push the throttle down slowly.
Cause:
Throttle has been pushed down too quickly.
Errors and changes excepted
Colours / final design – changes excepted
Technical changes and design-related changes excepted
Pictograms = symbolic photos
Chère cliente ! Cher client !
Nous vous félicitons pour l'achat de votre maquette d'hélicoptère Carrera RC
qui a été fabriqué selon le niveau actuel de la technique. Nous avons toujours
pour ambition d'améliorer et de perfectionner nos produits et nous réservons
la possibilité de réaliser des modifications techniques relatives à la présen-
tation et design de nos produits. Les divergences de faible importance du
produit, que vous avez acheté, par rapport aux données et illustrations de
ces instructions de montage et d'utilisation ne sauraient donner lieu à des
réclamations de ce fait. Ces instructions de montage et d'utilisation forment
partie intégrale du produit. Le fabricant décline toute responsabilité en cas
d'inobservation des instructions de montage et d'utilisation et des consignes
de sécurité y figurant. Veuillez conserver ces instructions de montage et d'uti-
lisation, afin que vous puissiez les consulter ultérieurement et et les remettre
à tout utilisateur de ce véhicule si besoin est.
Vous trouverez la version la plus actuelle de ce mode d'emploi et les
informations sur les pièces de rechange disponibles sur
dans la zone de service.
Conditions de garantie
Les produits Carrera sont des produits de qualité technique élevée qui
devraient être manipulés avec précaution. Veuillez impérativement res-
pecter les indications du mode d'emploi. Tous les éléments sont soumis
7
FRANÇAIS
.
4
carrera-rc.com

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Orange sply ii370501027x370501028x

Tabla de contenido