Nilfisk Advance 56116000 Instrucciones De Uso página 24

A - ENGLISH
DETERGENT SYSTEM USE (ECOFLEX)
Detergent Ratio (SCRUB SYSTEM MUST BE ON): See Figure 7-3.
No detergent is dispensed until the scrub and detergent systems are enabled and the Drive Pedal (3) pushed forward.
• The Detergent Indicator (C6) will be displayed in scrub mode when the detergent system is installed on the machine.
• The Detergent Ratio Indicator (C7) will display the selected ratio when the detergent system is on.
There are 4 modes of EcoFlex operation:
1A. Plain Water Cleaning Mode - During scrubbing, the detergent system can be turned off at any time by pressing the Detergent Switch
(Q) to allow scrubbing with water only. Detergent Ratio Indicator (C7) will be blank and Detergent Indicator Bar Graph (C8) will display
no bars fi lled. Detergent Light (Q1) will be off.
2A. Minimum Concentration Detergent Mode – Activated by pressing the Detergent Switch (Q) when detergent is off (repeated presses
will cycle to maximum Mode, off and back to minimum mode). Detergent Ratio Indicator (C7) will display the current minimum
detergent level and Detergent Indicator Bar Graph (C8) will display fi rst bar fi lled. Detergent Light (Q1) will be on. See below the
steps "To program the Minimum Detergent Level".
3A. Maximum Concentration Detergent Mode – Activated by pressing the Detergent Switch (Q) when detergent is at minimum mode
(repeated presses will cycle to minimum mode, off and back to maximum mode). Detergent Ratio Indicator (C7) will display the
current maximum detergent level and Detergent Indicator Bar Graph (C8) will display left and right bars fi lled. Detergent Light (Q1) will
be on. See below the steps "To program the Maximum Detergent Level". Do not use a concentration level exceeding the detergent
manufacturer's recommendation.
4A. Burst of Power Cleaning Mode – Pull the Burst of Power Paddle (S) to increase the detergent ratio for one minute to the pre-
programmed "maximum concentration" detergent level (as noted in programming instructions below). Detergent system will be turned
ON at "minimum concentration" detergent level if it was off. This will also cause the solution fl ow rate to increase to the next level and
the scrub pressure to increase to the next level. Burst of Power Indicator (C15) will blink for one minute on the display along with a 60
second timer countdown. Pull Paddle (S) again before 60 seconds to cancel Burst of Power. The amount of time Burst of Power runs
is adjustable (see "Information Menu Display" submenu "Options").
To program the Maximum Concentration Detergent Level
1. Press the OneTouch™ Scrub switch (E) to activate the scrub system.
2. Press and release Detergent Switch (Q) until you have entered the maximum concentration detergent mode ((C8) shows left and right
bars fi lled).
3. Press and hold the Detergent Switch (Q) for approximately 2 seconds until the Ratio Indicator (C7) fl ashes.
4. While the ratio is fl ashing, pressing and releasing the detergent switch will cycle through the available ratios (400:1, 300:1, 256:1, 200:1,
150:1, 128:1, 100:1, 64:1, 50:1, 32:1).
CAUTION!
Do not use a concentration level exceeding the detergent manufacturer's recommendation.
5. Once the desired ratio is displayed on the screen, stop and it will save the setting after 3 seconds.
6. Whenever the maximum concentration detergent setting is set to a lower concentration than the current minimum programmed
concentration setting, the minimum concentration default setting will be equal to the maximum concentration setting until changed by the
operator.
To program the Minimum Concentration Detergent Level
1. Press the OneTouch™ Scrub switch (E) to activate the scrub system.
2. Press and release Detergent Switch (Q) until you have entered the minimum concentration detergent mode ((C8) shows left bar fi lled).
3. Press and hold the Detergent Switch (Q) for approximately 2 seconds until the Ratio Indicator (C7) fl ashes.
4. While the ratio is fl ashing, pressing and releasing the detergent switch will cycle through the available ratios (Note: only ratios that are a
lower concentration or equal to the maximum detergent setting will be available.
5. Once the desired ratio is displayed on the screen, stop and it will save the setting after 3 seconds.
Once set, the detergent fl ow rate automatically increases and decreases with the solution fl ow rate, but the detergent ratio remains the same.
A - 24
INSTRUCTIONS FOR USE
SC6000 - 56091161 4/2016