Publicidad
Examine your kit carefully!
MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope
that you are happy with the contents of your kit. However, we would ask you to check all the parts before you start
construction, as we cannot exchange components which you have already worked on. If you find any part is not
acceptable for any reason, we will readily correct or exchange it. Just send the component to our Model Department.
Please be sure to include a brief description of the fault.
We are constantly working on improving our models, and for this reason we must reserve the right to change the kit
contents in terms of shape or dimensions of parts, technology, materials and fittings, without prior notification. Please
understand that we cannot entertain claims against us if the kit contents do not agree in every respect with the instructions
and the illustrations.
Caution!
Radio-controlled models, and especially model aircraft, are by no means playthings. Building and operating
them safely requires a certain level of technical competence and manual skill, together with discipline and a
responsible attitude at the flying field. Errors and carelessness in building and flying the model can result in
serious personal injury and damage to property. Since we, as manufacturers, have no control over the
construction, maintenance and operation of our products, we are obliged to take this opportunity to point out
these hazards, and to emphasise your personal responsibility.
Additional items required for the Mini Mag:
Adhesive and activator Use medium-viscosity cyano-acrylate adhesive ("medium cyano") in conjunction with activator
("kicker"). Do not use styrofoam cyano. Epoxy glues appear to produce strong joints, but the strength is only superficial
and the hard adhesive tends to break away from the components under stress. Hot-melt glue can also be used.
MULTIPLEX radio control equipment for the Mini Mag:
PiCO 5/6 UNI receiver
alternatively:
or:
Micro IPD UNI receiver
alternatively:
Nano S UNI or HS 55 servo (2 x required)
and (optional):
Nano S UNI or HS 55 servo (2 x required)
300 mm UNI extension lead
if necessary: 200 mm UNI separation filter cable
MagicMixer #1 for 3-channel transmitter without mixers
Y-lead (UNI) for 4-channel transmitter with separate rudder control
MULTIcont X-16 UNI
MULTIPLEX Permabatt NiMH flight battery (AA cells)
or
MULTIPLEX Permabatt NiMH flight battery (AA cells)
or
MULTIPLEX Li-Batt (Li-Po) flight battery P-CS
or
MULTIPLEX Li-Batt (Li-Po) flight battery SH BX
Battery charger:
MULTIcharger LN-5014 DC (charge current 100 mA ... 5 A) 1 - 14 NiCd/ NiMH
Optional:
Float set
Tuning 1: Easy Glider power set (3:1 gearbox and Permax 400)
plus 3.5 mm Ø propeller driver
and 8 x 3.8" propeller
Tuning 2: Powerset „sport" BL 22/18
Contents: motor, propeller driver, speed controller, propeller
Tools:
Scissors, balsa knife, combination pliers, cross-point / slot-head screwdrivers for servo output arm screws and motor
screws, soldering iron.
Note: please separate the illustrated pages from the centre of this booklet.
# 21 4211
35 MHz A
40 MHz
35 MHz A
40 MHz
Elevator / rudder
Ailerons
Aileron servos, 2 x
Aileron servos, 2 x
Speed controller
7 / 1500 mAh
8 / 1500 mAh
2 / 1-2000 mAh
2 / 1-2100 mAh
and 1 - 5 Li-Po cells
GB
Order No.
5 5920
Order No.
5 5921
Order No.
5 5971
Order No.
5 5972
Order No.
6 5120
Order No.
6 5120
Order No.
8 5031
Order No.
8 5035
Order No.
7 3000
Order No.
8 5030
Order No.
7 2271
Order No.
15 6030
Order No.
15 6037
Order No.
15 7016
Order No.
15 7130
Order No.
9 2531
Order No.
73 3069
Order No.
33 2688
Order No.
33 2310
Order No.
73 3139
Order No.
33 2627
21
Publicidad
