Sony KP-48V75 Manual De Instrucciones página 45

Operat ing a cable
box or DBS receiver
You can program the supplied remote control to
operate a cable box or DBS receiver. Follow the
procedures below to set the manufacturer's code
number in the remote control.
DISPLAY*
JUM P
TV/ DBS*
CODE SET
* The TV/DBS, GUIDE, DISPLAY, V/v/B/b/
buttons can be used only with a DBS receiver.
1
Turn of f t he equipm ent you w ant t o set up,
and press DBS/CABLE (FUNCTION).
2
Press t he CODE SET, DBS/CABLE (FUNCTION),
and 0 – 9 but t ons t o ent er t he
m anuf act urer's code num ber (see t he chart
on t he right colum n), t hen press ENTER. For
exam ple, t o program your rem ot e cont rol
t o operat e a Sony DBS receiver, press CODE
SET, DBS/CABLE (FUNCTION), 8, 0, 1, and
ENTER.
FUNCTION
CODE SET
DBS/CABLE
Downloaded from: https://www.usersmanualguide.com/
DBS/ CABLE (POW ER)
DBS/ CABLE
(FUNCTION)
1 2 3
0 – 9 buttons
4 5 6
7 8 9
0
ENTER
GUIDE*
*
V/v/B/b/
M ENU*
CH +/ –
, and MENU
FUNCTION
DBS/CABLE
8 0 1
3
Press DBS/CABLE (POWER) t o t urn on t he
cable box or DBS receiver.
4
Use t he cable box/DBS cont rol but t ons t o
check if t he code num ber w orks.
For example, to operate a cable box or DBS receiver,
you can use the DBS/CABLE (POWER), JUMP, CH
+/–, 0 – 9 and ENTER buttons.
Not e
• If the cable box or DBS receiver does not have a certain
function, the corresponding button on this remote control will
not operate.
To operat e t he project ion TV
Press TV (FUNCTION). Then use the projection TV
control buttons to control the projection TV.
For m ore det ails on operat ing t he cable box or
DBS receiver
Refer to the operating instructions that come with the
equipment.
If t he rem ot e cont rol doesn't w ork
• First, try repeating the setup procedures using the other codes
listed for your equipment.
M anuf act urer code num bers (cable box)
M anuf act urer
Hamlin/Regal
Jerrold/G. I.
Oak
Panasonic
Pioneer
Scientific Atlanta
Tocom
Zenith
M anuf act urer code num bers (DBS receiver)
M anuf act urer
Sony
RCA
Not es
• If more than one code number is listed, try entering them one
by one until you come to the correct code for your equipment.
• If you enter a new code number, the code number you
previously entered at that setting is erased.
• In some rare cases, your equipment may use a code that is not
provided with this remote control and you may not be able to
operate your equipment with the supplied remote control. In
this case, use the equipment's own remote control unit.
ENTER
• Whenever you remove the batteries — to replace them, for
example — if too much time is taken, the code numbers may
revert to the factory setting and must be reset.
DBS/CABLE
Code num ber
222, 223, 224, 225, 226
201, 202, 203, 204, 205, 206, 207, 208,
218
227, 228, 229
219, 220, 221
214, 215
209, 210, 211
216, 217
212, 213
Code num ber
801 (preset code for the supplied
remote control)
802
Operat ions
EN
45
-EN