Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-0000000502-001.book Page 32 Thursday, January 12, 2023 12:06 PM
en
32
Character
Unit of measurement,
international
2
m/s
h,DS
m, s, kg, A, mm, V, W,
N, °C, dB, min, m/s2
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
The hand-held, battery-powered angle grinder is
intended for cutting, roughing and brushing of metal
and stone materials as well as for drilling stone materials
with diamond hole cutters without the use of water.
For cutting with bonded abrasives, a special cut-off
wheel guard must be used.
When cutting in stone, provide for sufficient dust
extraction.
With approved sanding tools, the machine can be used
for sanding with sanding discs.
The power tool must not be used for grinding concrete.
Safety warnings common for grinding, sanding,
wire brushing or cutting-off operations
This power tool is intended to function as a grinder,
sander, wire brush, hole cutter or cut-off tool. Read all
safety warnings, instructions, illustrations and specifi-
cations provided with this power tool. Failure to follow
all instructions listed below may result in electric shock,
fire and/or serious injury.
Operations such as polishing are not to be performed
with this power tool. Operations for which the power
tool was not designed may create a hazard and cause
personal injury.
Do not convert this power tool to operate in a way
which is not specifically designed and specified by the
tool manufacturer. Such a conversation may result in a
loss of control and cause serious personal injury.
Do not use accessories, which are not specifically
designed and specified by the tool manufacturer. Just
because the accessory can be attached to your power
tool, it does not assure safe operation.
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fly apart.
Explanation
Mean vibrational value for sanding with sanding sheet
Basic and derived units of measurement from the international
system of units SI.
The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
The dimensions of the accessory mounting must fit the
dimensions of the mounting hardware of the power
tool. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pads for cracks, tear or excess
wear, wire brushes for loose or cracked wires. If power
tool or accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystand-
ers away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart
during this test time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye pro-
tection must be capable of stopping flying debris gener-
ated by various applications. The dust mask or respi-
rator must be capable of filtrating particles generated by
the particular application. Prolonged exposure to high
intensity noise may cause hearing loss.
Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury
beyond immediate area of operation.
Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your
control.
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your
body.
Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Publicidad
