Hypertherm HyPerformance Plasma HPR260XD Manual De Instrucciones página 259

4
D
Unit 1
HPR PAC
Dry Cutting System
CONTROL BOARD
S101
041993
ON
J106 J107
1 2 1 2
1 2 3 4
J303
C
1 2 3 4 1 2 3 4
141131
ETHERNET
INTERFACE
Machine Motion
BOARD
Jumper Block
S100
0
ON
1 2 3 4 5 6 7 8
Serial ID
UNIT ADDRESS
Dipswitch
J300A J300B J5
B
CNC Interface Cable
Notes:
1) For the 041993 control board, set Serial ID (S100), and Machine Motion (J303) as shown.
Jumpers J106 and J107 should be installed.
All 041993 DIPSWITCH and jumper settings are the same; serial IDs are determined
by the 141131 board setting.
2) For a single system installation, set SW1 on the 141131 board as shown in Unit 1.
3) For a two system installation, set SW1 on the 141131 boards as shown in Units 1 through 2.
4) For a three system installation, set SW1 on the 141131 boards as shown in Units 1 through 3.
5) For a four system installation, set SW1 on the 141131 boards as shown in Units 1 through 4.
A
4
3
Optional ArcGlide/EdgePro Multi-System Interface
Unit 2
HPR PAC
Dry Cutting System
CONTROL BOARD
S101
041993
ON
J106 J107
1 2 1 2
1 2 3 4
J303
1 2 3 4 1 2 3 4
ETHERNET
INTERFACE
Machine Motion
Jumper Block
S100
ON
SW1
1 2 3 4 5 6 7 8
Serial ID
UNIT ADDRESS
Dipswitch
J1 J300A J300B J5
CNC Interface Cable
ArcGlide Ethernet Cable
3
NUMERIK SRL - www.pantografosnumerik.com.ar
2
Unit 3
HPR PAC
Dry Cutting System
CONTROL BOARD
S101
041993
ON
J106 J107
1 2 1 2
1 2 3 4
J303
1 2 3 4 1 2 3 4
141131
Machine Motion
BOARD
Jumper Block
S100
0
ON
SW1
1 2 3 4 5 6 7 8
Serial ID
Dipswitch
J1 J300A J300B
CNC Interface Cable
ArcGlide Ethernet Cable ArcGlide Ethernet Cable
ArcGlide THC
and/or EdgePro Module(s)
2
1
Unit 4
HPR PAC
Dry Cutting System
CONTROL BOARD
041993
J106 J107
1 2 1 2
J303
1 2 3 4 1 2 3 4
141131
ETHERNET
INTERFACE
Machine Motion
BOARD
Jumper Block
S100
0
ON
SW1
1 2 3 4 5 6 7 8
Serial ID
UNIT ADDRESS
Dipswitch
J5 J1 J300A J300B
CNC Interface Cable
ArcGlide Ethernet Cable
Dipswitch setting example:
S100
ON
1 2 3 4 5 6 7 8
Switch 1 is in the On position
Switches 2-8 are in the Off position
ELEC SCH:HPR260XD POWER SUPPLY
013377
SHEET 19 OF 19
1
D
S101
ON
1 2 3 4
C
141131
ETHERNET
INTERFACE
BOARD
0
SW1
UNIT ADDRESS
J5 J1
B
A
E
7-23