Nilfisk-Advance Advenger 2800ST Instrucciones De Uso página 13

Ocultar thumbs Ver también para Advenger 2800ST:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

A-12 / ENGLISH
DETERGENT SYSTEM PREPARATION AND USE (AXP MODELS ONLY)
COMMON INSTRUCTIONS:
Pressing and releasing the Detergent Switch (E) while the solution system is active will cause the detergent system to alternately turn on and off. The system
should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over fl oor drain before purging because a small
amount of detergent will be dispensed in the process.
To Purge When Changing Chemicals:
1
Disconnect and remove the detergent cartridge.
2
Turn the Key Switch (A) ON. Press and hold the Solution Switch (C) and the Detergent Switch (E) down for 3 seconds. NOTE: Once activated the purge
process takes 20 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.
To Purge Weekly:
1
Disconnect and remove the detergent cartridge. Install and connect a Cartridge fi lled with clean water.
2
Turn the Key Switch (A) ON. Press and hold Solution Switch (C) and the Detergent Switch (E) down for 3 seconds. NOTE: Once activated the purge
process takes 20 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge the system.
When the Detergent Cartridge is almost empty a Display Panel (F4) indicator will come on. The "Low Detergent" indicator will remain on until you reset the
system. Once this indicator comes on you should be able to simply pour an entire gallon bottle of detergent into the Cartridge to refi ll without worrying about
measuring. NOTE: Only reset the system when the cartridge is full. When switching cartridges, the "Low Detergent" indicator is only accurate if the replacement
cartridge is at the same level as the cartridge being replaced.
To Reset:
1
Turn the Key Switch (A) ON. Press and hold the Solution Increase Switch (B) and the Solution Decrease Switch (D) down for 3 seconds. See illustration on
next page for Detergent System indicators.
Detergent Ratio:
1
The detergent ratio is locked at 1:400, except while overriding the EverGreen cleaning mode. The pre-programmed ratio that is used during EverGreen
override can be adjusted. With the detergent system OFF, press and hold the Detergent ON/OFF Switch (E) for 2 seconds. The detergent indicator will fl ash
and each press of the switch will cycle through the available ratios (1:32, 1:50, 1:64, 1:100, 1:128, 1:150, 1:200, 1:256, 1:300, 1:400). Once the desired ratio
is displayed on the screen (F5), stop and it will lock in after 5 seconds.
CARTRIDGE INSTRUCTIONS:
The Detergent Cartridge (13) is located behind the Detergent Cartridge Access Door (12) in the operator's compartment. Fill the detergent cartridge with a
maximum of 1.25 gallons (4.73 Liters) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to fi lling to avoid spilling
detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the
detergent name on each cartridge to avoid mixing them up. When installing a new cartridge, remove the Cap (AA) and place the cartridge in the detergent box.
Install the Dry Break Cap (BB) and detergent hose as shown.
FIGURE 5
A-12 - FORM NO. 56041735 - Advenger

Publicidad

Capítulos

Tabla de contenido
loading

Este manual también es adecuado para:

Advenger 3400st

Tabla de contenido