Publicidad
Idiomas disponibles
Idiomas disponibles
Familiarise yourself with the kit!
MULTIPLEX model kits are subject to continuous material monitoring during production. We hope that you will be
happy with the contents of the model kit. However, we ask you to check all parts (against the parts list) before
using them, as processed parts are non exchangeable. If a part should not function, we will be happy, after
checking the problem, to repair or replace the part. In such a case, please send the part to our model construction
department and do not forget to enclose proof of purchase and a short description of the fault.
We are continuously working on the technical improvement of our models. We reserve the right to modify the
contents of the kit with regard to shape, size, technology, material and features at any time and without notification.
Please understand that information and figures in these instructions cannot form the basis for a legal claim.
Warning!
Remotely controlled models, in particular aircraft models, are not toys in the conventional sense. Their
construction and operation requires technical understanding, at least some practical ability and care as
well as discipline and self-confidence. Faults and carelessness during construction and operation can
result in injury to people and damage to property. Because the manufacturer has no influence over the
correct assembly, maintenance and operation we expressly draw these hazards to your attention.
Additional Products Required for Assembly :
Remote control system
When ordering in North and South America add an "M" in front of the part number
MULTIPLEX receiver PiCO 5/6 UNI
or
MULTIPLEX receiver Micro IPD UNI
MULTIPLEX Servo Tiny S UNI (required 2 x)
MULTIPLEX PiCO- 400 round UNI
Drive Battery:
MULTIPLEX drive battery NiCd
or
MULTIPLEX drive battery Permabatt NiMh
or
MULTIPLEX drive battery NiCd
Charging unit:
MULTIcharger 4010 DC
Glue:
MULTIPLEX „Zacki leicht verdickt"
MULTIPLEX "Zacki Aktivator"
Alternatively, a similar superglue (cyanoacrylate glue) can be used, but do not use a superglue for polystyrene.
Epoxy glues initially provide reasonable adhesion, but if loaded, the hard glue will crack off. The adhesion is
only superficial.
Tools:
Scissors, craft knife, combination pliers, Ø 4-5 mm spike or small round file
Technical data:
wingspan
total length
fuselage length
weight during flight400 motor series / 6 AA cells
wing size
wing load
RC functions
Note: Remove the pages with the illustrations from the middle of the instructions for assembly!
Important information
This model is not made from polystyrene foam. For this reason it is not possible to use white glue or
epoxy glue. Please only use a cyanoacrylate glue, preferably one which is used in conjunction with an
activator (kicker). Please use a cyanoacrylate glue (superglue) of medium viscosity such as „ZACKi leicht
verdickt" With Elapor®, always spray one side with the activator (kicker) – leave it to dry and cover the
other side with the cyanoacrylate glue (ZACKi). Join the parts together and fix their position immediately.
GB
35 MHz A
40 MHz A
72 MHz
35 MHz A
40 MHz A
72 MHz
elevator / rudder
motor controller
6 / 500 mAh
6 / 1500 mAh
7 / 500 mAh
1370 mm
917 mm
870 mm
approx. 680 g
approx. 24 dm²
approx. 28 g/dm²
rudder, elevator and motor control
# 21 4192
order no. 5 5920
order no. 5 5921
order no. 5 5954
order no. 5 5971
order no. 5 5972
order no. 5 5973
order no. 6 5121
order no. 7 2292
order no. 15 5545
order no. 15 6019
order no. 15 5648
order no. 9 2527
order no. 59 2720
order no. 59 2824
15
Publicidad
