Dreame DreameBot D10s Manual Del Usuario página 7

Connecting with Dreamehome App
EN
This product works with the Dreamehome app, which can be used to
control your device.
Scan the QR code on the robot, or search " Dreamehome" in the app store to
download and install the app.
2. Add Device
Open the Dreamehome app, tap " " in the upper right, and scan the QR
code above again to add "DreameBot D10s". Please follow the prompts to
finish the Wi-Fi connection.
My Devices
Note:
Scan QR code on the device
• Only 2.4GHz Wi-Fi is supported.
• Due to upgrades in the app software, the actual operations may be different
Add Device
from the statements in this manual. Please follow the instructions based on the
Scan QR code to connect.
current app version.
10
3. Reset Wi-Fi
Simultaneously press and hold the buttons and until you hear a voice
prompt saying, "Waiting for the network configuration." Once the Wi-Fi
indicator is blinking slowly, the Wi-Fi has been successfully reset.
Wi-Fi Indicator
·Blinking slowly: To be connected
·Blinking quickly: Connecting
·On: Wi-Fi connected
Note: If your robot cannot connect to the app successfully, reset the Wi-Fi and
add the device again.
How to Use
1. Fast Mapping
After configuring the network for the first time, follow the instructions on
the app to quickly create a map, and the robot will start mapping without
cleaning. The mapping process will be completed when the robot returns to
the dock, and the map will be saved automatically.
2. Turn On/Off
Press and hold the button for 3 seconds to turn on the robot. The power
indicator should be illuminated. Place the robot onto the charging dock, the
robot should turn on automatically and begin charging. To turn off the robot,
move the robot away from the dock and press and hold the button for 3
seconds.
3. Start Cleaning
Press the button briefly to start cleaning after the robot is turned on.
Then, the robot will accurately map out a route, methodically clean along
the edges and walls, then finish by cleaning each room in an S-shaped
pattern to ensure a thorough job.
4. Cleaning Mode
DreameBot D10s has four cleaning modes: Quiet, Standard, Strong, and
Turbo. The default mode is Standard. You can specify the cleaning mode in
the app.
5. Pause/Sleep Mode
When the robot is running, press any button to pause it. If the robot is
paused for more than 10 minutes, it automatically enters sleep mode. All
indicators on the robot will turn off. Press any button on the robot, or use
the app to wake up the robot.
Note:
· The robot will turn off automatically if left in Sleep Mode for more than 12 hours.
· If the robot is paused and placed onto the charging dock, the current cleaning
task will end.
6. Spot Cleaning
When the robot is paused or in Standby Mode, press and hold the button
3 seconds to start Spot Clean Mode. In this mode, it will clean a square-shaped
area of 1.5×1.5 meters directly around the robot. When the spot cleaning
is done, the robot will automatically return to its original location and stop
working.
Note: Activating Spot Clean Mode will end the current cleaning task of the robot.
7. Do Not Disturb (DND) Mode
When the robot is set to the Do Not Disturb (DND) mode, the robot will be
prevented from resuming cleaning and the power indicator goes out. The DND
mode is disabled by default at the factory. You can use the app to enable the
DND mode or modify the DND period. The DND period is 22:00-8:00 by default.
Note:
· The scheduled cleaning tasks will be performed on time during the DND period.
· The robot will resume cleanup where it left off after the DND period expires.
8. Scheduled Cleaning
You can schedule cleaning time in the Dreamehome app. The robot will
automatically start cleaning at the designated time and then return to the
charging dock to recharge when the cleaning is done.
EN
for
11