Publicidad
Idiomas disponibles
Idiomas disponibles
3
4
3. Step on handle release pedal and lower
handle to operating position.
4. Turn cleaner ON.
CAUTION:
Do not clean over floor
electrical outlets.
CAUTION:
Water will drip from the
brushes and underside of the product after use
and may puddle. To avoid damage to wood and
laminate flooring and to avoid potential slip
hazard, after use A) do not leave the product
on wood and laminate surfaces and remove to
a hard surface and B) place unit on absorbent
material (such as a towel) to soak up drips.
5
6
5. Wash Mode - Lowers the SpinScrub™ brushes
to contact the floor for scrubbing action.
6. Dry Mode - Raises the SpinScrub™ brushes
off of the floor and also stops the spinning of
the brushes.
7
8
7. Scrub Mode - (FH40170 Series only) Lowers
the SpinScrub™ brushes to the floor and
stops the suction for extra cleaning with
solution and water. Switch to dry mode to pick
up any remaining dirty water.
TROUBLESHOOTING
If a minor problem occurs, it usually can be solved quite easily when the cause is found by using the checklist below.
Any other servicing should be done by an authorized service representative. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior
to continuing use.
WARNING:
To reduce risk of personal injury - Unplug before cleaning or servicing.
PROBLEM
Cleaner won't run
8. To release solution, squeeze trigger (A)
9
11
9. Slowly move cleaner forward and backward
over area to be cleaned. Squeeze trigger to
release solution as needed.
10. Overlap strokes by one inch to help prevent
streaking. The cleaner's suction will pick up
the dirty water throughout cleaning.
11. To remove those tough stains, apply extra
cleaning solution by squeezing the trigger (B)
as you normally would and pressing the Clean
Boost™ trigger (C) at the same time.
To greatly enhance drying of the floor surface,
release trigger. Continue to move cleaner over the
area to pick up the dirty solution.
Switch to dry mode to pick up any remaining
dirty water.
To continue cleaning another area, repeat steps
8 through10.
NOTE: When cleaning sealed wood floors, make
sure all areas are completely dry. Ensure that no
water remains on the floor.
Empty dirty water tank when the motor sound
becomes higher in pitch and there is a loss of
suction.
CAUTION:
Do not use the cleaner to
pick up flammable or combustible liquids or
chemicals.
A
POSSIBLE CAUSE
1. Power cord not firmly plugged into outlet.
2. No voltage in wall plug.
3. Blown fuse or tripped breaker.
4. Power switch not on.
MAINTENANCE
CLEANING THE NOZZLE
C
The cleaner's nozzle can be removed for easy
cleaning.
B
CAUTION:
from moving parts- Unplug before servicing. Do
not use cleaner without nozzle in place.
A
1
1. Pull on nozzle release latch (A) upward.
2. Remove nozzle by rotating nozzle.
Rinse nozzle under running water. Remove debris
from squeegee (C) and wipe with a damp cloth.
3
3. To reattach nozzle, tilt cleaner backwards so
the front of the foot is 2-3" off of the floor.
Secure upper handle with one hand and align
nozzle squeegee with base from left to right
with your other hand.
4. Simply rotate nozzle upward to lock in place.
CLEANING THE BRUSHES
The brush assembly can be removed for easy
cleaning when the nozzle is completely removed.
(See "CLEANING THE NOZZLE" section)
CAUTION:
from moving parts- Unplug before servicing. Do
not use cleaner without brushes in place.
Remove both tanks to prevent leaking. Set aside.
Remove nozzle (1-2).
Release foot pedal and tilt cleaner back so
handle rests on floor.
To reduce the risk of injury
5
5. Push two brush release buttons (B) and
remove the brush assembly.
6. The brushes can be washed with a mild
detergent and rinsed. Do not use a solvent
based detergent.
To replace brushes, align post (C) on brush block
2
with hole (D) on bottom of cleaner. Turn brushes
slightly until post fits easily into hole. Press
brush assembly firmly to snap into place.
Return cleaner to upright position. Replace nozzle
(4-5), making sure it is locked into position.
Return tanks into proper positions.
Any other servicing should be done by an
authorized service representative. If appliance
is not working as it should, has been dropped,
damaged, left outdoors, or dropped into water,
take it to a service center prior to continuing use.
STORAGE
4
STORING CLEANER
Turn cleaner OFF and disconnect from
electrical outlet.
• Empty and rinse Clean Water Solution Tank and
Dirty Water Tank. Allow to air dry.
• Make sure that nothing is pressing on the
nozzle squeegee.
• Do not store cleaner on a wood surface unless
cleaner is completely dry.
• Store appropriately indoors in a dry place. Do
not expose machine to freezing temperatures.
• Water will drip from the brushes and underside
of the product after use and may puddle. To
To reduce the risk of injury
avoid damage to wood and laminate flooring
and to avoid potential slip hazard, after use A)
do not leave the product on wood and laminate
surfaces and remove to a hard surface and B)
place unit on absorbent material (such as a
towel) to soak up drips.
POSSIBLE SOLUTION
1. Plug unit in firmly.
2. Check fuse or breaker in home.
3. Replace fuse/reset breaker in home.
4. Turn power switch on.
D C
B
6
Publicidad
