Descargar Imprimir esta página

SOLAC MV1501 Instrucciones De Uso página 9

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
Disassemble the handle,pull out the cord wrap.
(Fig. 3)
Push release tap on tube,then insert tube as-
sembled with handle into main body.Make sure
that the locking tab snaps into place.
Disassemble the tube,push release button on
back of main body, then pull it out.(Fig. 4)
USING STEAM MOP
Important:never use the steam mop without
the micro-fiber cleaning pad attached to the
mop head or without water in the water tank.
Sweep the floors before using the steam mop.
Place the micro-fiber cleaning pad underneath
the mop head.Make sure that the velcro are
facing up.(Fig. 5)
Important:always insure that the unit is "unplu-
gged" from the wall receptacle prior to filling
and before attaching the micro-fiber cleaning
pad to the bottom of the mop head.Never use
the steam mop without the micro-fiber cleaning
pad attached to the mop head.
Place steam mop on docking tray(Fig. 6)
Push the "PUSH"button on main body, lift up to
remove the water tank.(Fig. 7)
Turn the cap counter clockwise(Fig. 8),using
the filling funnel,pour the water into water tank.
Do not overfill the unit past the MAX fill line on
the water tank.
Replace cap onto the water tank.
Replace water tank onto main body.
Twist the quick release cord holder to unwrap
the power cord completely.
Plug into electrical outlet,the same to voltage
on rating plate.
Press the power switch. The power-on light will
glow red while the mop is heating up.
Select the level of steam in the handle using
the buttons on the handle to raise or lower the
mode (low, medium or high). (Fig. 9)
It takes approximately 45 seconds for the unit
to heat up and the steam to be ready.
Once hot, the power light will flash green while
in the upright position and solid green while in
use.
Wait seconds,dampen the micro-fiber cleaning
pad first, begin mopping with a forward and
backward motion,it will release steam as you
mop.
When water tank is empty,the steam mop will
stop emitting steam.Unplug the power cord
from the electrical outlet and refill the water
tank following the instructions above.
When the unit is under vertical stand, the pump
will stop working for the static protection
Remove cleaning pad,put carpet glider to
clean the tile at home.
FEATURES
Steam mop utilizes steam to remove tough
grease, dirt and grime. Cleaning house without
using harsh chemicals, therefore it is perfect-
ly ecological. It can be used to clean your tile,
hardwood, ceramic tile, linoleum and vinyl
floors.
Quick&easy
Eliminates rinsing, wringing, carrying buckets
of water and redistributing the dirt on the floor.
Save your time to clean up the floors.
Sanitizing
Powerful steam helps for superior cleaning and
sanitizing. Kill 99,99% of viruses and germs
No chemical used
Use tap water or distilled water, perfectly eco-
logical.
Quick Start-up
Steam is ready in just 45 seconds
Reusable and washable cleaning pad
Static Protection
When the unit is under vertical stand, the pump
will stop working for the static protection
Energy saving for battery
Without touching select switch, it will stop wor-
king to prolong use time for battery.
CARE AND MAINTENANCE
If you consistently use distilled water, cleaning
the water tank is not necessary.
CAUTION:
This appliance must be unplugged from the
electrical outlet before performing any cleaning
or maintenance tasks on the unit.
Care the micro-fiber cleaning pad
Wash the pad with a mild detergent.
Put it in washing machine using the warm wa-
ter setting, and separately from other fabrics or
placing them in a garment bag first.
RINSING OUT THE STEAM MOP
Let the appliance cool down completely before
cleaning or storing.
Empty all water from the water tank after each
use.
EN

Publicidad

loading