Manuales relacionados para Truper SOMI-130T
Resumen de contenidos para Truper SOMI-130T
- Página 1 Manual MIG Welder 130 A Applies for: Code Model 13192 SOMI-130T SOMI-130T Read the user’s manual thoroughly CAUTION before operating this tool.
- Página 2 Contents CAUTION Technical Data Power Requirements To gain the best performance of the tool, prolong the duty life, General Power Tool Safety Warnings make the Warranty valid if necessary, and to avoid hazards Safety Warnings for Welders of fatal injuries please read and understand this Manual before Parts using the tool.
- Página 3 Technical specifications SOMI-130T Code Description MIG Welder 13192 INPUT Voltage Frequency 127 V 60 Hz Current Rated Input Capacity 22.6 A 2.8 kVA OUTPUT Welding Process MIG / FCAW Open Circuit Voltage 57 V c.c. Current Range 30 A - 90 A c.c.
- Página 4 General Power Tools Safety Warnings WARNING! Read carefully all safety warnings and instructions listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
- Página 5 Safety Warnings for Welders To Prevent Fire Protection Equipment for Welding • Wear welding helmet to protect your WARNING CAUTION • Always have handy a fire extinguisher eyes and face when working with the welder. Double check in good working conditions. the shadow lens of the welding helmet is right for the welding WARNING •...
- Página 6 Safety Warnings for Welders • Inspect the cylinders for outer corrosion, CAUTION Gas Handling indentations, lumps, holes or wells. If not sure if some • Gas used in the welding processes are inert gases that do not imperfection is acceptable under these guidelines, stop using the react under normal conditions.
- Página 7 Parts Handle Gas Hose Micro Wire Control Spool Seal Panel Torch Micro Wire Feeding Mechanism Ground Cable Cabinet Lock Clamp to Ground the Work Piece Inlet Energy Thermal Indicator Protection Light Light Tension Control Feed Cord Micro Wire On / OFF Speed Control Switch Ventilation...
- Página 8 • CO mixed with Argon reduces the weld spatters while working. • To weld aluminum, use Argon Gas. CAUTION For best results, it is recommended to use original Truper brand parts and accessories, such as: AN-SOMI-130, BOQ-SOMI-130/210, TOB-SOMI-130/210, P-SOMI ENGLISH...
- Página 9 Installation Micro Wire Spool CAUTION • Turn off and disconnect the welder before opening the cabinet door. • Push the cabinet locks upwards ( I ) to open and gain access to the micro wire feeding system. • Loosen the fastener knob (J) remove the knob, the spring (O) and the fastener (N) from its axis (K).
- Página 10 Installation Micro Wire Feed 1. Loosen the fastening knob (A) from the wire feeding mechanism. 2. Lower the adjusting knob to release the rod cover. 3. Lift the rod cover (G) and fit at least 12” wire (H) into the wire feeding mechanism guide.
- Página 11 Installation Micro Wire Feeding Rhythm • Connect the welder to the power supply and turn on the • Adjust pressure on the micro wire using the tension welder switch to verify the micro wire feeding rhythm. knob (L). Consider that excessive pressure hinders the •...
- Página 12 Start Up Connection Configurations CAUTION • All the connections in the control panel shall be fully tightened in their respective power outlet. Secure the connections turning in a clockwise direction. • The electrode polarity can be modified depending of the soldering job requirements or needs. Remember making tests in scrap material to define the right configuration before working on the work piece.
- Página 13 Use this control to select the appropriate voltage or current for the job to be performed, from a minimum value (position 1) to a maximum value (position 10). VOLTAGE MICRO WIRE SPEED SOMI-130T Output Output Knob value voltage (V) Current (A) 15.50...
- Página 14 Start Up Operation Overload Protection • To assure the flowing of the electric circuit clean 0.7” to • The welder is built with a thermal protection to guard 1.2” around the zone where the grounding clamp will be against overload. When an overload strikes, the welder will connected and around the zone to be welded to the work automatically turn off and the overload light (H) will light pieces.
- Página 15 Start Up Welding Examples Overlapped Joint Weld applied Very fast electrode correctly movement and / or very low current Very slow electrode movement and / or very high current Electrode too separated from the work piece Spyral movement Half-moon movement Bevel Zig-zag Angle welding...
- Página 16 Maintenance • The right use and good maintenance extend the useful life of the welder. Micro Wire Feeding Mechanism CAUTION • Only qualified staff shall carry out repairs. Visit a Authorized Service • Verify regularly the micro wire feeding mechanism. Center to repair the welder and purchase supplies or Cleaning the feeding rod notches (A) is indispensable to accessories.
- Página 17 Troubleshooting Problem Cause Solution The energy source is • The overload protector is activated due to • Energy is reestablished automatically when the interrupted. overheating. unit is back to the adequate temperature. After 15 minutes approximately. There is no soldering •...
- Página 18 Troubleshooting Problem Cause Solution The welding pearl is • Welding current is too low. • Increase the speed and current to the micro wire. very narrow and bulky. • Welding speed is too fast. • Move the torch slower and / or make circular movements or zig zag movements with the nozzle.
- Página 19 Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center.
- Página 20 It includes the costs of transportation of the product that derive from its fulfillment of its service network. . Phone number 800-018-7873. Made in China. Imported by Truper, S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257, Phone number 761 782 9100.