Publicidad
Idiomas disponibles
Idiomas disponibles
Rev5_01/2021- PROTIG III S A
PROTIG III S
10 - 20 - 30 - 40
Instructions for safety, use and maintenance
References of various models
PROTIG III S
10 RL
20 RL
30 RL
40 RL
Connection C5B original, complete with banana plug.
Technical data
TIG manual torch with natural cooling
PROTIG III S
Duty cycle 35%
Curent
Duty cycle 60%
Light alloy welding, reduce the duty cycle about 30%
Voltage class
Gas flow
Ø 1.0 / 3.2 mm Ø 1.0 / 3.2 mm Ø 1.0 / 4.0 mm Ø 1.0 / 4.8 mm
Using electrodes
Back Cap
Origin
equipment fitted
Nozzle
Ø 10 mm
to the torch
Electrode
Safety instructions
We thank you for your trust in our company by purchasing this equipment which will provide you with
complete satisfaction if you comply with its conditions for use and maintenance.
CAUTION: The company declines all responsibility in case of modification, addition of components
or subassemblies, or any transformation of the equipment carried out by the customer or a third-
party, without prior specific written agreement from the company.
Arc welding and plasma cutting may be dangerous for the operator and persons close to the work
area. Read the operating manual and safety instructions W000261712. See www.weldline.eu.
A) Maintenance / Troubleshooting
Before any internal verifications and repair work, make sure that the equipment is separated from
the electric installation by electrical isolation (by electrical isolation is meant a group of operations
designed to separate and keep the equipment de-energized).
At least every six months, you must check the proper condition of the insulation and connections of
the electric equipment and accessories such as plugs, flexible wires, ducts, connectors, extension
leads, part-holders, electrode-holders, or torches...
Maintenance and repair work on the jackets and insulating ducts must be carried out extremely
carefully.
Have defective parts repaired by a specialist, or better still, have them replaced.
Routinely check the proper tightening and cleanliness of the electric connections.
Lincoln Electric Iberia S.L.
Ctra. Laureà Miró 396-398, 08980 Sant Feliu de Llobregat (Barcelona) - Spain
5 m
8 m
W000382715-2
W000382716-2
W000382717-2
W000382718-2
W000382719-2
W000382720-2
W000382721-2
W000382722-2
10
20
30
125 A
150 A
200 A
80 A
100 A
130 A
L- 113V
Mini : 7 l/min - Maxi 13 l/min
Long
Long
Long
Ø 10 mm
Ø 12 mm
Ø 1.6 L
Ø 2.0 L
Ø 2.4 L
B) Work-station
Use only electrode holders and torches which are perfectly insulated.
The operator must be insulated from the ground-surface and the workpiece (gloves, safety shoes, dry
clothes, leather apron, and so forth...).
Do not touch the electrode wire and the part (or the nozzle) simultaneously.
C) Protection
It is absolutely essential that your protect your eyes from blinding glare (glare of arc invisible light and
infrared and ultraviolet radiation).
The welding mask, without or with helmet, must always be equipped with a protective filter whose
gradation depends on the welding arc current intensity (EN 169 Standard).
Fumes emitted during welding operations may be dangerous. Use adequate protection means (fumes
extraction, ventiled masks...)
Option :
Adjustable head
Index
Reference
200
W000279381
201
W000279383 - 125 A 35%
202
W000279384 - 145 A 35%
40
W000270829
250 A
200 A
Maintenance boxes
Reference
W000306441
W000306442
Long
W000306443
Ø 12 mm
W000306444
Ø 2.4 L
Extension
Reference
W000306135
EN 60974-7
For a good thermal contact
use a grease containing
copper.
Description
Torch body bent, replacing the body PROTIG 10 and PROTIG 20
Head PROTIG 10
Head PROTIG 20
Female connection M12x1. To connect power sources
not accepting the Quick Connection Gas
Description
WEAR PARTS BOX TIG 10
WEAR PARTS BOX TIG 20
WEAR PARTS BOX TIG 30
WEAR PARTS BOX TIG 40
Description
EXTENSION AIR 15M
EN
www.weldline.eu
Publicidad
