Publicidad
Idiomas disponibles
Idiomas disponibles
emissions, increase in operating flexibility thanks to the modu-
lation of air flow and increase in the level of comfort in terms of
temperature, humidity and noise levels.
The range is made up of 12 models with air flows from 300 to
1200 m³/h.
Continuous modulation of the air flow and the use of high-ef-
ficiency heat exchangers enables operation also with small
air-water temperature differences.
MAIN COMPONENTS
Structure
Built from galvanised steel sheet, heat and sound insulated by
means of Class 1 self-extinguishing panels. Reduced height to
facilitate installation in a horizontal position in a false ceiling. The
structure incorporates a drip tray and condensate drain outlet.
The main condensate drip tray is situated inside the structure of
the unit and is at a positive pressure relative to the drain outlet
to facilitate condensate drainage.
Heat exchanger
High efficiency 3 and 4 rows heat exchanger made with copper
piping and aluminium fins blocked to pipings by mechanical ex-
pansion, provided with brass manifolds and air vent valve.The
heat exchanger usually comes with water connections mounted
on the left, but it can be turned by 180°. High-efficiency heat
exchangers optimized for district cooling applications are avail-
able on request.
Fans
Double suction centrifugal fans made with ABS or alumini-
um, with statically and dynamically balanced forward-curving
ACCESSORIES
Electronic microprocessor control panels with display
DIST
MY COMFORT controller spacer for wall mounting
EVOBOARD
Circuit board for EVO control
EVODISP
User interface with display for EVO controller
MCLE
Microprocessor control with display MY COMFORT LARGE
MCSUE
Humidity sensor for MY COMFORT (medium e large), EVO
MCSWE
Water sensor for MYCOMFORT and EVO controllers
Electronic microprocessor control panels
TED 10
Electronic controller for BLDC fan equipped with inverter and ON/OFF valves 230 V
TED SWA
Water temperature sensor for TED controls
Auxiliary water drip trays, insulating shell, condensate drainage pump
KSC
Condensate drainage pump kit
Electrical heating elements
RE
Heating element with installation kit, relay box and safety devices
Air inlet and outlet grilles
GA
Aluminium air intake grille, with frame
GM
Aluminium air outlet grille with 2-row fins and subframe
Valves
V2VDF+STD 2-way valves, ON/OFF or MUDULATING actuator, 230 V or 24 V power supply,
hydraulic kit, for main and additional heat exchanger
2-way valve, ON/OFF or MODULATING actuator, 230 V or 24 V power supply, hydraulic
V2VSTD
kit, for main heat exchanger
3-way valves, ON/OFF or MODULATING actuator, 230 V or 24 V power supply,
V3VDF
hydraulic kit, for additional heat exchanger
2-way valves, ON/OFF or MODULATING actuator, 230 V or 24 V power supply,
V3VSTD
hydraulic kit, for main heat exchanger
2-way valves pressure independent, ON/OFF or MODULATING actuator, 230 V or 24 V
VPIC
power supply, hydraulic kit, for main heat exchanger
18
DUCTIMAX I
The heat exchangers can also be optimized in the circuit for cen-
tralized applications such as district cooling.
Operation is controlled from wall-mounted microprocessor con-
trol panels with display, such as the MYCOMFORT LARGE and
EVO models which also enable DUCTIMAX i to be connected to
GARDA.
The action of the G3 air filter can be combined with an air ionisa-
tion system available as an accessory.
blades, directly coupled to the electric motor.
EC Motor
Single-phase asynchronous multi-speed electric motor with per-
manently connected capacitor and thermal protector, mounted
on vibration-damping supports.
Air filter
Washable air filter, made of acrylic fibre, filtration class G2 or G3,
applied on the air intake; may be pulled out from below.
Air intake
Air intake from the front or bottom of the unit, according to sys-
tem requirements. See figure 13.15 p. 73 and 13.16 p. 74.
Installation example
see figure: 13.3 p. 65
The bearing structure allows to combine a large range of acces-
sories in suction and air delivery in order to obtain the optimized
unit configuration.
Plenum, air intake modules, air inlet and outlet connectors and cabinets
MAF90
Air intake module with G3 air filter
MAFO
Air intake module with G4 air filter
MAFO90
Air intake module with G4 air filter
PAF
Intake and delivery plenum, not insulated, with spigot Ø 200 mm
PMA
Intake and delivery plenum, not insulated, with spigot Ø 200 mm
PMAC
Intake and delivery plenum, insulated, with spigot Ø 200 mm
R90
90° uninsulated air inlet/outlet connector
R90C
90° uninsulated air inlet/outlet connector
RD
Straight uninsulated air inlet/outlet connector
RDC
Straight insulated air inlet/outlet connector
Flexible ducts - caps
TFA
Not insulated flexible ducts, Ø 200 mm (6 m lenght undivisible)
TFM
Insulated flexible ducts, Ø 200 mm (6 m lenght undivisible)
TP
Plastic cap Ø 200 mm
Air inlet and outlet plenum box
CA
Air Inlet plenum box with double row grille
CAF
Air Inlet plenum box with double row grille 300 x 600 mm and filter G2
CM
Insulated air outlet plenum box with grille
Accessories
VRC
Auxiliary water drip tray
Publicidad
