Bresser 47-01170 Instrucciones De Uso página 11

Automatic telescope
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
General Information
About this Instruction Manual
Please read the safety instructions in this manual carefully. To avoid
damage to the unit and the risk of injury, only use this product as
described in the manual.
Keep the instruction manual handy so that you can easily look up infor-
mation on all the functions.
CAREFUL
You will find this symbol before every section of text
that deals with the risk of minor to severe injuries
resulting from improper use.
ATTENTION
You will find this symbol in front of every section of
text which deals with the risk of damage to property
or the environment.
Intended Use
This product is intended only for private use.
It was developed for the magnified display of things in nature.
General Warning
RISK OF BLINDNESS
Never use this device to look directly at the sun or in the direct
proximity of the sun. Doing so may result in a risk of blindness.
CHOKING HAZARD
Children should only use the device under adult supervision.
Keep packaging material, like plastic bags and rubber bands,
out of the reach of children, as they pose a choking hazard.
FIRE RISK
Do not place the device, particularly the lenses, in direct sun-
light. The concentration of light could cause a fire.
RISK OF ELECTRIC SHOCK
This device contains electronic components which operate
via a power source (power supply and/or batteries). Children
should only use the device under adult supervision. Only use
the device as described in the manual; otherwise, you run the
risk of an electric shock.
RISK OF CHEMICAL BURN
Keep batteries out of the reach of children! Make sure you
insert the batteries correctly.
could cause burns if they come into contact with the skin. If
necessary, wear adequate gloves for protection.
RISK OF FIRE/EXPLOSION
Do not expose the device to high temperatures. Use only the
recommended batteries. Do not short-circuit the device or bat-
teries, or throw them into a fire. Excessive heat or improper
handling could trigger a short-circuit, a fire or an explosion.
ATTENTION
Do not disassemble the device. In the event of a defect, please
contact your dealer. The dealer will contact the Service Centre
and can send the device in to be repaired, if necessary.
Privacy Protection
This device is intended only for private use. Please
heed the privacy of other people. Do not use the
device to look into apartments, for example.
Manual_4701180-4701181_de-en-fr-it-es-ru_BRESSER_v082020a.indd 11
Manual_4701180-4701181_de-en-fr-it-es-ru_BRESSER_v082020a.indd 11
Empty or damaged batteries
Accessories may vary depending on the model.
Parts overview (No. 1-8)
B
Telescope tube
C
Tube opening
D
Eyepiece connection
E
Focus wheel
F
Handbox
G
Eyepiece holder
H
Handbox tray
I
Azimuthal lock
J
Tripod
1!
Battery compartment
1@
Locking screw
1#
Accessory tray
1$
Altitude locking knob
1%
Dust cover
1^
Eyepieces
1&
Moon filter
1*
Compass
1(
Star map
2)
Software CD
Handbox (No. 9)
B
Red light source
C
Handbox display
D
Plus/minus key
E
Illumination
F
Centre key
G
Arrow keys
H
Number pad
I
Mini-USB port
1
J
RJ-45 port
1
1)
RJ-22 port
1
NOTE:
1
The ports of the handbox (8, 9 and 10) are prepared for future develop-
ments, but are not active at the moment. Currently there are no addi-
tional accessories (e.g. serial cable etc) available. Information about
new developments for this product can be found on our website under
www.bresser.de/download/automatic_telescopes
Part I – Construction
1. General/Location
Before you begin assembly, choose a suitable location for your tel-
escope. It is best to build the telescope in a place where you have a
clear view of the skies, a stable footing and sufficient space around
you.
Before beginning assembly, remove all the parts from the packaging,
and, using the diagram, check to make sure no parts are missing.
2. Tripod
Take the tripod (9) out of the box. Carefully open the legs and place the
tripod on a level surface place and lock the accessory tray (13) on the
centre knob and rotate until it snaps in place (No. 3).
Note: Please do not forget to remove the accessory tray before
collapsing the tripod.
3. Telescope
Loosen the screw (12) in the dovetail mount so that it is completely
retracted (No. 4). Place the telescope with the dovetail in the mount
and tighten the screw. Make sure that the BRESSER logo is upright.
4. Altitude knob
Loosen the vertical knob by rotating it anticlockwise, align the optical
telescope tube (1) horizontally and retighten the knob (No. 5).
5. Mount
Place the mount base's mounting holes on the tripod's mounting
screws and tighten them (No. 6).
EN
11
17.08.2020 08:07:47
17.08.2020 08:07:47

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

47-01180

Tabla de contenido