Publicidad
Idiomas disponibles
Idiomas disponibles
v) maintain a handhold whilst working from a ladder or take additional safety
precautions if you cannot.
4.5 Repair, maintenance and storage
Repairs and maintenance must be executed only by qualified technicians hired by the FARAONE
assistance centre: +39 0861.772221 - info@faraone.com.
The ladders must be cleaned with a cloth soaked in water or alcohol.
The ladders must be stored in a dry environment not exposed to the elements.
Ladders made of or containing thermoplastic, thermosetting and reinforced plastic materials
should be stored away from direct sunlight.
Wooden ladders should be stored in a dry place and must not be coated with matte and
vapour-resistant paint.
4.6 Demolition of the ladders
Do not dispose of the ladders in the environment. Deliver them to authorized recycling centres.
5 INSTRUCTIONS FOR THE USE OF ALL MODELS OF LADDERS
5.0 How to assemble the outriggers for models: SELLA, SAS, T1,
TELES TT, SUPER TELES and TELES
1. Position the template
(fig.1) and drill the
uprights where the holes
are meant to be made.
2. Remove the template and
screw on the plates (fig.2)
To close the outrigger,
unscrew the side knobs and
rotate the pipe towards the
ladder.
OPERATING AND SAFETY INSTRUCTION MANUAL . 44
1
2
5 INSTRUCTIONS FOR THE USE OF ALL MODELS OF LADDERS
ATTENTION!
Before using the ladder, read carefully the general norms
(from page 36 to page 44).
5.1 SINGLE LADDER
MAX 150 Kg
EN 131.1
EN 131.2*
D.L. 81
1) Place the ladder ready to be used.
2) Anchor the ladder on top with a
belt or another device, in order to
avoid any sliding or side skidding
risk.
3) Insert the outriggers (to ensure
compliance with standard 131.2
2018. See paragraph 5.0 on
page 44)
* With stabilizers
HANDRAIL INSTALLATION
BRS.01
Standard for mod. SAS, optional for mod. T.1
1. BRS.01 positioning
2
1
FIX THE FIRST
FIRST HANDRAIL
CHECK THE
PLATE ON THE PIN
IN LINE WITH THE
DISTANCE
PLATE
BETWEEN
GUARDRAIL AND
FIRST STEP
2. Back hook positioning
3
3. Middle handrails
positioning
MAX. 1 cm
CONNECT THE
PLACE THE INTERMEDIATE
TUBE / HOOK
HANDRAILS MAKING SURE THEY
REAR WITH THE
ARE AS CLOSE AS POSSIBLE TO
APPROPRIATE
EACH OTHER
NECKTIE
Next >
45. OPERATING AND SAFETY INSTRUCTION MANUAL
AVAILABLE ARTICLES
Mod. SELLA
S10/E - S14/E
SAS Series
SAS.200 - SAS.250 - SAS.300
SAS.350 - SAS.400 - SAS.450
EN 14122
SAS.500 - SAS.550
T.1 Series
T200/1 - T250/1 - T300/1 - T350/1 -
T400/1 - T450/1 - T500/1 - T550/1
SA.1
SA10/1 - SA12/1 - SA14/1
BRS.02
Optional
1. BRS.02 positioning
1
FIX THE FIRST
FIRST HANDRAIL
CHECK THE
3
PLATE ON THE PIN
IN LINE WITH THE
DISTANCE
PLATE
BETWEEN
GUARDRAIL AND
2
FIRST STEP
2. Posizionamento
braccioli intermedi
MAX. 1 cm
3. Hook installation
PLACE THE INTERMEDIATE
HANDRAILS MAKING SURE
THEY ARE AS CLOSE AS POS-
SIBLE TO EACH OTHER
03
33
65
Publicidad
