Publicidad
Idiomas disponibles
Idiomas disponibles
ATTENTION!
Before using the ladder, read carefully the general norms
(from page 36 to page 44).
5.10 LADDER FOR WAREHUSES MOD. SMT
STABILISING BAR ASSEMBLY
1) Take off one of the feet from the
stabilising bar by taking out the
screw (1).
2) Position the stabilising bar in the
slots on the holes (2).
3) Screw the cap onto the profile
using the previously-removed
screw (3).
4) Assemble the 2 aluminium plugs
onto the base of the element, so
that the stabilising bar is also
MAX 150 Kg
locked into place (4).
5) Open the ladder so that the
landing is flat. (5).
6) Secure the side bars with the
wheels. (5A).
ATTENTION:
7) Assemble the two side handrails. (5B).
The user nust
8) Assemble the protective railing. (5C).
put on thesa-
9) Place the ladder whereneeded.
fety
10) Open the side outriggers (if any).
belt when ope-
11) Adjust and lock the outriggers in
rating from the
place using the knobs.
top board.
The ladder is now ready for use.
5.11 WAREHOUSE LADDER WITH VERTICAL BACK
MAX 150 Kg
EN 131.7
D.L. 81
1) Follow the instructions as for
"Warehouse ladder at Items from
1 to 9 page 56.
2) Secure the ladder using the SICUR
STOP system (assembly diagram
on next page).
3) For ladders taller than 2.40 m,
apply the supplied ballast.
4) The ladder is now ready for use.
Next >
OPERATING AND SAFETY INSTRUCTION MANUAL . 56
AVAILABLE ARTICLES
Mod. SMT
70/SMT - 100/SMT
125/SMT - 150/SMT
1
200/SMT - 250/SMT
275/SMT - 300/SMT
325/SMT - 350/SMT
375/SMT - 400/SMT
2
450/SMT - 500/SMT
3
4
AVAILABLE ARTICLES
Mod. MF.TS
100/MFTS - 125/MFTS
150/MFTS - 200/MFTS
250/MFTS - 275/MFTS
1
300/MFTS - 325/MFTS
350/MFTS - 375/MFTS
400/MFTS - 450/MFTS
ATTENTION: The user must
put on thesafety belt when
operatingfrom the top board
(1).
ATTENTION!
Before using the ladder, read carefully the general norms
(from page 36 to page 44).
SICUR STOP: ASSEMBLY DIAGRAM
1) If not already assembled, install
the base carriage. Place the base
carriage under the ladder (fig. 1).
3) Position the handle between the carriage
and the steps (fig. 2).
4) Fit the side crossbeams between the ladder
and the handle (fig. 3).
5) Insert the bolts as
3
shown in the figure (fig. 4).
5.12 PROFESSIONAL LADDER MOD. PL
MAX 150 Kg
EN 131.7
D.L. 81
1) Undo the safety belts (1).
2) Open the step ladder so that the
steps are flat, taking care not to
place your hands in the joints.
3) Climb onto the ladder and close
the protection (2).
4) The ladder is now ready for use.
5) To close the ladder back up: lift the
protection, get down from the
ladder, close the ladder by lifting
the working platform (3), taking
care not to place your hands in the
joints.
6) Do up the safety belts
57. OPERATING AND SAFETY INSTRUCTION MANUAL
1
2
4
P
A
AVAILABLE ARTICLES
Mod. PL
PL3 - PL4 - PL5 - PL6
1
3
2
03
33
65
Publicidad
