Beninca ZED24E Manual De Instrucciones página 15

Declaration in accordance with Directives 2004/108/CE(EMC); 2006/95/CE(LVD); 2006/42/CE(MD) Annex II, part B
The Manufacturer: Automatismi Benincà SpA
Address: Via Capitello, 45 - 36066 Sandrigo (VI) - Italy
Declares that the product:
Electromechanical actuator 24V DC for tilt-up doors, model:
ZED24 - ZED 24E
conforms with the requirements of the following EC Directives:
• DIRECTIVE 2004/108/CE OF THE EUROPEAN PARLIAMENT AND COUNCIL, 15 December 2004, in relation to the harmonisation
of the legislation of member states regarding electromagnetic compatibility , in abrogation of Directive 89/336/CEE, per the following harmo-
nised standards:
EN 61000-6-2:2005, EN 61000-6-3:2007.
• DIRECTIVE 2006/95/CE OF THE EUROPEAN PARLIAMENT AND COUNCIL, 12 December 2006, in relation to the harmonisation
of the legislation of member states regarding electrical material intended to be used within certain voltage ranges, per the following harmonised
standards:
EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008; EN 60335-1-103:2003.
• DIRECTIVE 2006/42/CE OF EH EUROPEAN PARLIAMENT AND COUNCIL, 17 May 2006, in relation to machinery, amending Di-
rective 95/16/CE, in relation to the requisites for "partly completed machinerys", per the following harmonised standard: EN13241-1:2003.
• Automatismi Benincà SpA declares, furthermore, that the pertinent technical documentation has been completed in conformity with Annex
VII B of Directive 2006/42/CE and that the following essential requisites have been satisfied: 1.1.1 - 1.1.2 - 1.1.3 - 1.1.5 - 1.2.1 - 1.2.3 - 1.2.6 -
1.3.1 - 1.3.2 - 1.3.3 - 1.3.4 - 1.3.7 - 1.3.9 - 1.5.1 - 1.5.2
- 1.5.4 - 1.5.5 - 1.5.6 - 1.5.7 - 1.5.8 - 1.5.10 - 1.5.11 - 1.5.13 - 1.6.1 - 1.6.2 - 1.6.4 - 1.7.2 - 1.7.4 - 1.7.4.1 - 1.7.4.2 - 1.7.4.3.
• The manufacturer agrees to forward the pertinent information regarding the "partly completed machinery" to the national authorities if justifiably
requested to do so. This agreement includes the means of transmission and does not affect the manufacturer's intellectual property rights.
• The "partly completed machinery" may not be put into service unless the machine into which it is to be incorporated has been declared con-
forming - as applicable - to the requirements of Directive 2006/42/CE.
Benincà Luigi, Legal representative.
Sandrigo, 02/11/2010.
IntrOduCtIOn
We congratulate you for choosing the ZED24 gear motor. All the
items in the vast Benincà range are the fruit of twenty years of ex-
perience in the sector of automatisms and of a continuous search
for new materials and state-of-the-art technologies. For this very
reason, today we are able to offer extremely reliable products
which, thanks to their power, efficiency and long life, fully satisfy
the demands of the end user. All our products are made in con-
formity with the regulations in force and are covered by guarantee.
Moreover, a TPL policy stipulated with a leading insurance com-
pany covers any damage to persons or things caused by manu-
facturing defects.
1. generaL InfOrmatIOn
For good operation of this automation, the overhead door must
possess the following characteristics:
- good robustness and rigidity
- good balancing
- good sliding of the guides.
In any case, it must be possible to perform manual opening and
closing with ease.
2. generaL CharaCterIstICs
ZED24 is an automation for overhead doors with counterweights,
for central or side assembly. Compact and linear, the ZED24 gear
motor adapts to any type of overhead door. As well as guarantee-
ing maximum reliability, ZED24 offers a continuous, regular and
silent movement. It is easy to fit using screws or welding. The gear
motor is irreversible which ensures that the door can be closed
without the use of electric locks. In the event of a power cut the
door may be released by simply turning a knob on the gear mo-
tor.
CE Declaration of Conformity
Central assembly with welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• pair of galvanized tubes with bush AU.45Z (1500 mm) or AU.45ZL
(2000 mm);
• pair of galvanized straight arms AU2.D. If there is no space, use
the pair of galvanized bent arms AU2.C (see Fig. 6).
Central assembly with welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• pair of galvanized tubes with bush AU.45Z (1500 mm) or AU.45ZL
(2000 mm);
• pair of straight arms with bush AU2.DNS (600 mm).
Central assembly with welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• splined bush AU.45B; if the geared motor is too far from the edge
of the door, use the pair of tubes with welded bush AU2.45T (150
mm);
• pair of galvanized straight arms AU2.D. If there is no space, use
the pair of galvanized bent arms AU2.C (see Fig. 6).
Lateral assembly without welding:
• fitting plate AU.65 (650 mm), AU.125 (1250 mm) or AU.20 (2000
mm);
• pair of straight arms with welded bush AU2.D45 (600 mm) or
AU2.D45L (2000 mm); if the geared motor is too far from the edge
of the door, use the pair of tubes with welded bush AU2.45T (150
mm) with the pair of straight arms with bush AU2.DNS (600 mm).
3. aCCessOrIes fOr assembLy
15