Publicidad
Idiomas disponibles
Idiomas disponibles
PRECAUTIONS ON USING CIRCULAR SAW
1. Use only blade diameter specified on the machine.
2. Do not use any abrasive wheel.
3. Do not use saw blades which are deformed or cracked.
4. Do not use saw blades made of high speed steel.
5. Do not use saw blades which do not comply with the
characteristics specified in these instructions.
6. Do not stop the saw blades by lateral pressure on the
disc.
7. Always keep the saw blades sharp.
8. Ensure that the lower guard moves smoothly and freely.
9. Never use the circular saw with its lower guard fixed in
the open position.
10. Ensure that the retraction mechanism of the guard
system operates correctly.
11. Never operate the circular saw with the saw blade
turned upward or to the side.
12. Ensure that the material is free of foreign matters such
as nails.
13. For model C7MFA, the saw blades range shall be from
180 mm to 190 mm.
14. Disconnect the plug from the receptacle before carrying
out any adjustment, servicing or maintenance.
15. Check that there are no nicks or scratches in the cord.
16. Check the exterior and ensure that there is no damage.
17. Use a saw blade with a displayed rotational speed
equal to or higher than the rotational speed of the tool.
18. Use a saw blade that suits each different cutting
material.
19. Always hold handle of the tool firmly.
SPECIFICATIONS
Model
Voltage (by areas)*
90°
Cutting Depth
45°
Power Input
No-load speed
Weight (without cord)**
* Be sure to check the nameplate on product as it is subject
to change by areas.
** According to EPTA-Procedure 01/2014
STANDARD ACCESSORIES
(1) Saw Blade (mounted on tool) .......................................1
(Dia. 185 mm ...................... C7MFA)
(2) Box Wrench ..................................................................1
(3) Guide ............................................................................1
(4) Wing-bolt ......................................................................1
(5) Lever (short type) .........................................................1
(6) Dust collector ...............................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Washer (A)
....................... for 20 mm (Hole dia. of saw blade)
....................... for 30 mm (Hole dia. of saw blade)
(2) Guide Rail Adapter
Optional accessories are subject to change without notice.
C7MFA
(110 V, 230 V, 240 V) ~
68 mm
46 mm
1010 W
5800 min
–1
3.6 kg
APPLICATION
Cutting various types of wood.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prepare a wooden workbench (Fig. 1)
Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
CAUTION
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
5. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
ADJUSTING THE POWER TOOL PRIOR TO USE
1. Adjusting the cutting depth
The cutting depth can be adjusted by moving the base
after loosening its lever (A) (Fig. 2).
CAUTION
Should this lever (A) remain loosened, it will create a
very hazardous situation. Always thoroughly clamp it.
2. Adjusting the angle of inclination
By loosening the wing bolt at the scale, the saw blade
can be titled up to maximum angle of 45° against the
base (Fig. 3).
The angle of inclination can also be regulated by
loosening the wing bolt at the scale (Fig. 3).
CAUTION
It is very hazardous to allow this wing bolt to remain
loosened. Always thoroughly clamp it.
3. Regulating the guide
The cutting position can be regulated by moving the
guide to the left or right after loosening its wing bolt.
The guide can be mounted on either the left or the right
side.
4. Fine tuning of parallelism
It is possible to fine-tune the parallelism of the saw
blade to the base using the parallelism adjustment
screw.
Adjustment has already been made at the time of
shipment from the factory. However, in the unlikely
event of parallelism being faulty, adjust as follows.
(1) Unfasten only the mounting screws of the saw cover
hinge portion (Fig. 4).
(2) Retract the protective cover into the saw cover.
(3) Insert wood chip in the rear side of the saw blade
base, and mark the position on the base (Fig. 5).
English
9
Publicidad
