Publicidad
Idiomas disponibles
Idiomas disponibles
BELT OR BRUSHROLL: REMOVAL & REPLACEMENT
TOOL REQUIRED: PHILLIPS SCREWDRIVER
NOTE: Unplug cleaner before changing belt or brushroll.
BELT STYLE
For Belt Style 5 replacement, please visit our website at www.dirtdevil.com to buy
5
online or call customer service at 1-800-321-1134.
REMOVAL
1.
Screws
Tab
Tab
Lay cleaner flat and flip cleaner over to
expose nozzle base. Base should lay flat and
face up. To remove nozzle guard, use a
Phillips Screwdriver to remove the three (3)
screws. Arrows show location of screws.
Push on the two tabs to release. Lines show
location of tabs. Lift nozzle guard off.
3.
2.
1
Insert brushroll into side holder #1
Place new belt in area
and then #2. Follow direction of
of brushroll without
arrows on brush end caps, (Diagram
bristles.
3a). NOTE: Rotate brushroll to make
sure belt is not twisted.
GENERAL MAINTENANCE
WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE SERVICING.
IF OBSTRUCTION DEVELOPS DURING FLOOR CLEANING:
1. If obstruction develops while cleaning carpets, turn cleaner OFF and unplug. Check paper bag to see if it is
full. If full, replace with a new paper bag (Page 8).
2. Check dirt tube to see if there is an obstruction (Page 6, "HOSE ASSEMBLY").
If so, remove obstruction.
3. Turn cleaner over and remove nozzle guard (Page 9, Diagram 1). Clear any obstruction that occurs in or
around the brushroll area.
4. Remove hose from hose inlet (Page 7, Diagram 7). Remove any obstruction.
NOTE : Regularly clean debris from filter in bag compartment (Page 8).
IF OBSTRUCTION DEVELOPS DURING TOOL USAGE:
1. If obstruction develops while above floor cleaning, turn cleaner OFF and unplug. Check paper bag to see
if it is full. If full, replace with a new paper bag (Page 8).
REPLACEMENT
1.
2.
Lift and remove brushroll.
Loop belt onto motorshaft.
Dispose of old belt.
4.
3a.
Tab
Tab
2
Tab
Replace nozzle guard. Match the front tabs
to the slots on the nozzle base first. Swing
down to snap hooks. Press firmly on entire
nozzle guard to secure. Replace the three
(3) screws to secure. IMPORTANT: Rotate
brushroll by hand before starting cleaner.
9
TOOL REQUIRED: FLATHEAD SCREWDRIVER
WARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK - UNPLUG CLEANER BEFORE REMOVING OR
REPLACING LIGHTBULB.
NOTE:This cleaner uses a common automotive lamp #906, 13.0 volts. For bulb replacement, call
1-800-321-1134 or your local auto parts store.
1.
MOTOR
SHAFT
WARNING: TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING
PROBLEM
Cleaner won't run
Cleaner won't
pick-up or low
suction
Dust escaping
from cleaner
Cleaner tools won't
pick-up
Headlight not
working
ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
In the event that further assistance is required, see your Yellow Pages for an authorized Royal
www.dirtdevil.com. Costs of any transportation to and from any place of repair are to be paid by the owner. The service parts used
in this unit are easily replaced and readily available from an authorized Royal
model number and manufacturing code when requesting information or ordering replacement parts. (The model number appears
on the bottom of the cleaner.)
LIGHTBULB: REMOVAL & REPLACEMENT
2.
Lean cleaner handle
back. Insert end of
standard (flat head)
screwdriver into bottom
slot and pry outward to
pop headlight lens out.
TROUBLESHOOTING GUIDE
POSSIBLE REASON
POSSIBLE SOLUTION
1. Power cord not firmly plugged into
1. Plug unit in firmly.
outlet.
2. Blown fuse or tripped breaker.
2. Check fuse or breaker in home. Replace
fuse/reset breaker.
3. Needs service.
3. Take to service center. To find nearest location,
visit our website at www.dirtdevil.com or call
1-800-321-1134.
4. Thermal protector activated.
4. Allow cleaner to cool - Pg. 3.
1. Paper bag is not opened.
1. Insert finger into hole and push paper away
from opening - Pg. 8.
2. Paper bag full.
2. Replace paper bag - Pg. 8.
3. Brushroll worn.
3. Replace brushroll - Pg. 9.
4. Broken or worn belt.
4. Replace belt - Pg. 9.
5. Nozzle/hose clogged.
5. Remove nozzle/hose guard to clear blockage
Pg. 6 & 9.
6. Unit misassembled resulting in air
6. Reassemble unit / review assembly - Pg. 6.
flow leakage.
7. No paper bag in cleaner.
7. Install bag and clean filter - Pg. 8.
1. Paper bag full.
1. Replace paper bag - Pg. 8.
2. Bag not installed correctly.
2. Review paper bag installation - Pg. 8.
3. Puncture/hole in paper bag.
3. Replace paper bag - Pg. 8.
4. No bag in cleaner.
4. Install bag - Pg. 8.
5. Hose not connected correctly.
5. Review Hose Installation - Pg. 6.
1. Hose clogged.
1. Remove hose and tools; remove obstruction -
Pg. 6.
2. Paper bag full.
2. Replace paper bag - Pg. 8.
3. There is an obstruction.
3. Review General Maintenance - Pg. 9.
1. Bulb burnt out.
1. Replace bulb - Pg. 10.
2. Loose electrical wires.
2. Take to service center. To find nearest location,
visit our website at www.dirtdevil.com or call
1-800-321-1134.
CUSTOMER SERVICE (1-800-321-1134)
®
Dealer or retailer. Always identify your cleaner by the
10
Pull bulb out of socket to
remove. Push bulb into
socket to replace. Snap
headlight lens panel
back into place.
®
Dealer or visit our website at
Publicidad
