HIKOKI C 7SS Instrucciones De Manejo página 6

English
7. Never use the circular saw with its lower guard fi xed in
the open position.
8. Ensure that the retraction mechanism of the guard
system operates correctly.
9. Never operate the circular saw with the saw blade
turned upward or to the side.
10. Ensure that the material is free of foreign matters such
as nails.
SPECIFICATIONS
Model
Voltage (by areas)*
Cutting Depth
Power Input*
No-Load Speed
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES (INCLUDE SIDE
HANDLE)
(1) Saw Blade (mounted on tool) .......................................1
(
Dia. 165 mm........................C6SS
Dia. 190 mm .......................C7SS
(2) Hex. Bar wrench ...........................................................1
(3) Guide ............................................................................1
(4) Side handle ...........................................................1 or 0
The items that are included as standard accessories
(including the side handle) vary depending on the region.
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Dust Collector Set (D)
Connect the suction hose to collect saw dust with the
vacuum cleaner (see Fig. 9).
(2) Washer (A)
........ for 20 mm (Hole dia. of saw blade)
Optional accessories are subject to change without notice.
APPLICATION
Cutting various types of wood.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
6
90o
45o
)
11. For model C6SS, the saw blades range should be
from 165 mm to 160 mm.
For model C7SS, the saw blades range should be
from 190 mm to 185 mm.
12. Disconnect the plug from the receptacle before
carrying out
maintenance.
C6SS
(120 V, 127 V, 220 V)
57 mm
38 mm
1050 W
5500/min
3.2 kg
4. Prepare a wooden workbench (Fig. 1)
Since the saw blade will extend beyond the lower surface
of the lumber, place the lumber on a workbench when
cutting. If a square block is utilized as a workbench,
select level ground to ensure it is properly stabilized. An
unstable workbench will result in hazardous operation.
CAUTION
To avoid possible accident, always ensure that the
portion of lumber remaining after cutting is securely
anchored or held in position.
5. How to store the hex. bar wrench (Fig. 8)
The hex. bar wrench used for attaching and detaching
the saw blade can be stored in the handle.
ADJUSTING THE POWER TOOL PRIOR TO USE
1. Adjusting the cutting depth
The cutting depth can be adjusted by moving the base
after loosening its lever (A) (Fig. 2).
CAUTION
Should this lever (A) remain loosened, it will create a very
hazardous situation. Always thoroughly clamp it.
2. Adjusting the angle of inclination
By loosening the wing bolt at the scale, the saw blade
can be titled up to maximum angle of 45° against the
base (Fig. 3).
The angle of inclination can also be regulated by
loosening the wing bolt at the scale (Fig. 3).
CAUTION
It is very hazardous to allow this wing bolt to remain
loosened. Always thoroughly clamp it.
3. Regulating the guide
The cutting position can be regulated by moving the
guide to the left or right after loosening its wing bolt.
The guide can be mounted on either the left or the right
side.
CUTTING PROCEDURES
1. Place the saw body (base) on the lumber, and align the
cutting line with the saw blade at the front scale (Fig.
4).
any adjustment, servicing
C7SS
68 mm
46 mm
3.4 kg
or