Publicidad
CARE AND MAINTENANCE
Your PVXp 10 is a sturdy and durable product and will provide years of reliable use if properly cared for. Use
common sense and read the safety warnings to avoid hazardous operating conditions.
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing to
qualified service personnel.
Sunlight/Heat
Avoid prolonged exposure to direct sunlight, as this may cause the unit to overheat and thermally shut off.
Excessively hot operating conditions can also cause a thermal shutdown. Do not store in extremely hot or cold
conditions or extremely high humidity. Always allow unit to come to room temperature before use.
Cleaning
Never clean the PVXp 10 while plugged in or turned ON! When the unit has been fully disconnected from AC
power sources, use a dry cloth to remove soil or other dirt. Never use strong solvents on the PVXp 10, as they
could damage the cabinet. Do not allow ANY fluids to drip inside the PVXp 10.
Touchup
For an overall finish enhancement and protective coating, use gloves to apply a plastic finish protector, such as
Armor-All
protectant or a similar product, to the surface of the plastic cabinet only. Note that the cabinet will be
®
slippery after these treatments; rub them down vigorously with a dry, lint-free cloth to minimize this.
Check for Secure Hardware
After the first few months of use and periodically thereafter, check the hardware of the PVXp 10 for tightness,
including the rear panel screws and the screws that hold the baffle and rear cabinet together. The unit is subject
to a great deal of vibration, and this could cause them to loosen with use.
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The powered loudspeaker system shall have a frequency response from 65 Hz to 20 kHz. The peak SPL with
inaudible distortion shall reach 122 dB with music as a source, when measured at a distance of 1M and driven to
full output capacity. The system shall utilize a Peavey Pro 10 10" heavy-duty woofer and a Peavey RX 10N dynamic
compression driver . The nominal radiation pattern shall be 100° in the horizontal plane, and 60° in the vertical
plane. Axis of the vertical main polar lobe is angled down 10 degrees, resulting in the angular pattern with respect
to straight ahead being +20, -40 degrees
The powered, bi-amplified loudspeaker system shall have an input channel consisting of a medium impedance
input connector consisting of one combo female XLR and 1/4" TRS phone jack on the rear panel.
The input section shall have a Contour EQ system activated by a pushbutton that provides for boost at the low and
high frequencies of about 5 dB relative to the midrange.
There shall be a group of Thru (output) connectors consisting of a male XLR jack, and a 1/4" TRS phone jack.
The system power amplifiers shall have an unfiltered frequency response o 20 Hz to 20 kHz which deviates no
more than +0, -3 dB up to rated power, a damping factor greater than 100 @ 1 kHz into 8 ohms, hum and noise
better than 90 dB below rated power, and THD and IMD of less than 0.5%.
The woofer amplifier shall be capable of 150 W continuous before thermal pull-back to into an 8 ohm nominal load,
and the tweeter amplifier shall be capable of 50 W continuous output into a 8 ohm load, and both shall incorporate
independent DDT compression.
The input signal shall be electronically divided into high frequencies and low frequencies by a staggered pole
fourth order slope line-level crossover at 3.1 kHz. The low frequencies shall be processed to provide bass boost,
subsonic filtering and overall response shaping, and the high frequencies shall be equalized for response-shaping.
The enclosure shall be constructed of injection-molded ABS with a UL flame rating, and reinforcing ribs internally.
A handgrip shall be incorporated on the top rear of the cabinet.
A separate powder-coated metal grille shall be provided for horn and woofer protection. The cabinet shall
incorporate a pole mount for speaker stand use, four tall sturdy rubber feet for floor standing use, and a group of
two widely spaced inserts, and a rectangular grouping of four mounting point inserts on the top and bottom each,
and on the right side (delete), for flying use.
Publicidad
