BIEMMEDUE GE 46 HC Manual De Instrucciones página 13

Before using the space heater, carefully read all of the instructions and follow them scrupulously.
The manufacturer cannot be held responsible for damage to persons and/or property caused by improper use of
the equipment.
This instruction manual is an integral part of the equipment and must therefore be stored carefully and passed on
with the unit in the event of a change of ownership.
GENERAL RECOMMENDATIONS
The space heaters run on diesel fuel. Direct combustion
versions send hot air and combustion products into the room,
while indirect combustion versions are fitted with a flue to
discharge the fumes through the chimney.
Warning
THIS HEATER IS FOR PROFESSIONAL USE. IT
HAS BEEN CAREFULLY DESIGNED FOR MOBILE
AND TEMPORARY
APPLICATIONS.
IT HAS NOT BEEN DESIGNED FOR DOMESTIC
USE NOR FOR COMFORT HEATING AND SHOULD
NEVER BE USED TO HEAT CLOSED ROOMS
WITHOUT ADEQUATE VENTILATION.
Always follow local ordinances and codes when using this
heater:
• Follow the instructions in this booklet very carefully;
• Use only in places free of flammable vapours or high dust
content;
• Keep inflammable material at a safe distance from the heater
(minimum 3 metres);
• Make sure fire fighting equipment is readily available;
• Ensure that the machine resting surface or ground is not made
of flammable material;
• Make sure sufficient fresh outside air is provided according to
the heater requirements. Direct combustion heaters should
only be used in well vented areas in order to avoid carbon
monoxide poisoning;
• the indirect combustion heater is installed near a chimney to
take away the fumes (see the paragraph "FUMES FLUE
POSITIONING DIAGRAM") and connected to an electrical
switchboard;
• nothing is obstructing the aspiration and expulsion of air;
movement of air may be obstructed in various ways including
placing covers or other objects on the heater or positioning the
heater too near a wall or other large object;
• In case of very low temperatures add kerosene to the heating
oil;
• Make sure heater is always under surveillance and keep
children and animals away from it;
• Before starting the heater always check free rotation of
ventilator;
• Unplug heater when not in use.
SAFETY DEVICES
The heater is fit with an electronic device that controls the
flame and the maximum safe temperature by means of a
photocell and an overheat thermostat.
The electronic device controls start/stop times and trips the
safety in case of malfunctions. It has reset button (13) that can
assume different colours (Function Light) depending on the
function mode:
• off: heater is in idle mode or in "stand-by" mode, waiting for
heating request;
• steady green: heater functioning normally;
• steady red: heater in safety stop;
• flashing orange: heating interrupted due to excessive
variations in voltage supply (T<175V or T>265V); heating will
EN
IMPORTANT
Warning
Warning
PROFESSIONAL
cause of the stop before you restart the heater. Push button (13)
for at least 5 seconds to launch a self-diagnosis programme,
after which the button will assume different colours (Self-
diagnosis light) depending on the type of safety that tripped:
• flashing orange: false flame detected during restart cycle.
• flashing red: no flame during restart cycle.
• flashing red/green: no flame during work cycle.
• steady orange: internal error of electronic device.
Warning
OPERATION
it into the electrical power supply, check that the power supply
specifications are the same as those stated on the identification
plate.
Warning
Warning
surface in order to prevent it from overturning and/or diesel leaks
from the tank filler cap.
13
resume automatically when voltage returns in range from 190
V and 250 V.
To restart heating after a safety stop, push reset
button (13) for 2 seconds.
NEVER do more than two restarts in a row:
uncombusted diesel fuel may accumulate in the
combustion chamber and suddenly flare up at the
next restart.
If the safety stop persists, you have to find and eliminate the
See "TROUBLESHOOTING" to identify the cause of
the malfunction.
Before switching on the heater and, therefore, before plugging
For models "DV" check that the arrows on the
voltage supply selector key cover are pointing to
the voltage value required.
If necessary:
• remove the cover;
• press deflector (18) to the position required;
• replace the protective cover.
• The power line must be earthed and fitted with a
residual current circuit breaker.
• The heater plug must be inserted into a socket
equipped with a mains switch.
The heater must be placed on a flat, stable, and levelled