Publicidad
Idiomas disponibles
Idiomas disponibles
• Before switching on the machine, always
check that the shredding unit, shredding
unit screws and other attachments are
well secured and that the protective de-
vices and shields are in place. Replace
worn and damaged parts in sets to avoid
imbalance. Worn or damaged labels
must be replaced.
• Before use, always inspect the connec-
tion and extension lead for signs of dam-
age or ageing. If the lead is damaged
during use, it must be disconnected from
the mains supply immediately. DO NOT
TOUCH THE LEAD BEFORE IT IS DIS-
CONNECTED FROM THE MAINS. Do
not use the machine if the lead is dam-
aged or worn.
• Never use the device when persons and
especially if children or animals are near-
by.
• Only use spare or accessory parts which
are supplied or recommended by the
manufacturer. Using third-party parts
leads to a loss of guarantee claims.
• Do not leave the device running unat-
tended and store the device in a dry
place, out of the reach of children.
• Only connect the device to a properly
earthed mains. Sockets and extension
cables must have a functional protective
conductor.
• When using outdoors, the device must
be connected to a socket with a residual
current device (RCD) with a rated leak-
age current of no more than 30 mA.
• Always stay outside of the ejection zone
when commissioning the machine.
Operation:
• Before starting the device, make sure that
the filling funnel is empty.
• Keep your face, head, hair and body a
safe distance from the filling funnel.
• Do not place hands, other parts of the
body and clothing in the filling chamber,
the ejector chute or in the vicinity of other
moving parts.
• Always pay attention to your balance
and firm footing. Do not overreach.
When feeding material, never stand on
a higher level than the level of the base
of the machine.
• Do not stay in the ejection area when op-
erating the machine.
• Ensure that hard objects such as metal,
stones, glass, bottles, cans or other for-
eign objects are not contained in the ma-
terial being thrown in.
6
GB/IE
• If foreign objects get into the cutting tool
or the machine makes unusual noises or
vibrates abnormally, switch the motor off
immediately and allow the machine to
run down. Disconnect the machine from
the mains and take the following steps
before restarting and operating the ma-
chine:
- Check the machine for damage
- Check the parts for firm seating, retight-
en them if necessary.
- Repair or replace any parts with parts
that are of equivalent quality.
• Do not let processed material pile up
within the ejection area; this could pre-
vent proper ejection and cause a kick-
back of the material through the filling
funnel.
• In the event of blockages in the loading
or discharge area of the machine, switch
off the motor and pull the mains plug be-
fore removing material remaining in the
filling funnel or ejector chute. Make sure
that the motor is free of waste and other
accumulations to safeguard the motor
from damage or possible fire. Remem-
ber that when the starter mechanism with
motorised machines is commissioned, the
cutting tool also starts operating.
• Do not reach into the filling funnel during
operation. The device continues to run
for a short time after switching off.
• Warning! Never operate the machine
with faulty protective devices or covers
or without protective devices or with a
damaged or worn cable.
• Keep the motor clean of debris and other
accumulations to prevent damage to it or
possible fire.
• Do not transport or tilt the device with the
motor running.
• Stop the machine and remove the plug
from the power socket. Ensure that all
moving parts have come to a complete
stop:
- when the device is not in use, is being
transported or is unattended;
- before freeing a jammed blade.
- before clearing a blockage or cleaning
blocked ducts;
- when checking the device, it is raining or
when removing blockages;
- when cleaning or performing mainte-
nance or changing accessories;
- when the power or extension cable is
damaged or tangled;
- when you want to move or lift the device;
- when foreign bodies get into the device,
in the event of unusual noises or vibra-
tions (check the device for damage be-
fore restarting).
Publicidad
