Publicidad
Idiomas disponibles
Idiomas disponibles
become noisier.
Please note:
Before installing the cooker hood, perform the following
steps as indicated in figure 4:
1 - Remove both the cooker hood body B and the glass
panel A from the packaging and place them horizontally
on a secure surface.
2 - Take the glass panel A and position it above the cooker
hood body B.
3 - Fix the glass panel securely to the cooker hood body
using the 4 sleeves C and 4 screws D as indicated.
• FIXING TO THE WALL
Drill the holes A respecting the distances indicated
(Fig.2). Fix the appliance to the wall and align it in
horizontal position to the wall units. When the appliance
has been adjusted, definitely fix the hood using the
screws A (Fig. 5 - Stage 2). For the various installations
use screws and screw anchors suited to the type of wall
(e.g. reinforced concrete, plasterboard, etc.). If the screws
and screw anchors are provided with the product, check
that they are suitable for the type of wall on which the
hood is to be fixed.
• FIXING THE DECORATIVE TELESCOPIC FLUE -
EXTRACTOR VERSION
Warning! Before fixing the appliance in place, take the
lower connector and use a pair of pliers to bend the tab
inwards, as shown in figure 5, stage 1.
Arrange the electrical power supply within the dimensions
of the decorative flue. If your appliance must be installed
as an extractor version, make sure an air exhaust hole
has been prepared. Adjust the width of the suppor t
bracket of the upper flue (Fig.3). Then fix it to the ceiling
using the screws A (Fig.3) in such a way that it is in line
with your hood and respecting the distance from the
ceiling indicated in Fig.2. Connect the flange C to the air
exhaust hole using a connection pipe (Fig. 5 - Stage 2).
Insert the upper flue into the lower flue. Fix the lower
flue to the hood using the screws B provided (Fig. 5 -
Stage 2), extract the upper flue up to the bracket and fix
it with the screws B (Fig.3). Remove the charcoal filters
already fitted to the appliance by turning them 90°
anticlockwise (Fig. 7).
• FILTERING VERSION
Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting version.
The charcoal filters are already fitted to the appliance.
USE AND MAINTENANCE
• We recommend that the cooker hood is switched on
before any food is cooked. We also recommend that the
appliance is left running for 15 minutes after the food is
cooked, in order to thoroughly eliminate all contaminated
air.
The effective performance of the cooker hood depends
on constant maintenance; the anti-grease filter and the
active carbon filter both require special attention.
• The anti-grease filter is used to trap any grease
particles suspended in the air, therefore is subject to
saturation (the time it takes for the filter to become
saturated depends on the way in which the appliance is
used).
- To prevent potential fire hazards, the anti-grease filters
should be washed a minimum of every 2 months (it is
possible to use the dishwasher for this task).
- After a few washes, the colour of the filters may change.
This does not mean they have to be replaced.
If the replacement and washing instructions are not
followed, the anti-grease filters may present a fire hazard.
• The active carbon filters are used to purify the air
which is released back into the room. The filters are not
washable or re-usable and must be replaced at least once
every four months. The active carbon filter saturation level
depends on the frequency with which the appliance is
used, the type of cooking performed and the regularity
with which the anti-grease filters are cleaned.
• Clean the cooker hood frequently, both inside and
outside, using a cloth which has been dampened with
denatured alcohol or neutral, non-abrasive liquid
detergents.
• The light on the cooker hood is designed for use during
cooking and not for general room illumination. Extended
use of the light reduces the average duration of the bulb.
•COMMANDS: (Fig.9) MECHANICAL the key symbols
are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
• Replacing halogen light bulbs (Fig. 8).
To replace the halogen light bulbs B, remove the glass
pane C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare hands.
CUSTOMER ASSISTANCE SERVICE
Before contacting the Technical Assistance Service:
If the product does not operate at all, we advise you to:
- check that the plug has been inserted into the power
socket correctly.
If you cannot identify the cause of the operating anomaly:
switch off the appliance (do not subject it to rough
treatment) and contact the Assistance Service.
PRODUCT SERIAL NUMBER. Where can I find it?
It is important that you inform the Assistance Service of
your product code and its serial number (a 16-character
code which begins with the number 3); this can be found
on the guarantee certificate or on the data plate located
inside the appliance.
This will help to avoid wasted journeys being made by
technicians, thereby (and most significantly) saving the
corresponding callout charges.
THE
MANUFACTURER
RESPONSIBILITY FOR EVENTUAL DAMAGES
CAUSED BY BREACHING THE ABOVE WARNINGS.
- 15 -
DECLINES
ALL
Publicidad
