Makita DLM461 Manual De Instrucciones página 13

Removing the mulching attachment
For DLM460
1. Open the rear cover.
► Fig.4: 1. Rear cover
2.
Remove the mulching attachment while holding
down the lever.
► Fig.5: 1. Lever 2. Mulching attachment
For DLM461
1. Open the rear cover.
► Fig.6: 1. Rear cover
2. Remove the mulching attachment while pulling the lever.
► Fig.7: 1. Mulching attachment 2. Lever
Assembling the grass basket
1. Pick up the upper clip of the grass basket.
► Fig.8: 1. Upper clip
2. Insert the frame into the grass basket as far as it
will go while holding the handle of the frame.
► Fig.9: 1. Handle
NOTICE:
Do not insert the handle into the grass
basket. Be sure to insert the frame along the stitch of
the grass basket.
3. Make sure that there is no sagging on the corners
of the grass basket.
► Fig.10
4. Open the upper clip, and attach it to the frame.
► Fig.11
5.
Attach all the other clips as shown in the figure.
Make sure that all the clips are securely attached to the
frame.
► Fig.12: 1. Clip
► Fig.13
Installing the grass basket
1. Open the rear cover.
► Fig.14: 1. Rear cover
2. Hook the grass basket on the rod of the mower
body as shown in the figure.
► Fig.15: 1. Rod 2. Guard 3. Grass basket
NOTICE:
Make sure that the guard on the grass
basket is facing downward. Otherwise, the grass
basket may not catch all of cut-off grass.
Attaching the mulching attachment
For DLM460
1. Open the rear cover, and then remove the grass
basket.
► Fig.16: 1. Rear cover 2. Grass basket
2.
Attach the mulching attachment while holding
down the lever, and then release the lever to lock the
mulching attachment.
► Fig.17: 1. Lever 2. Mulching attachment
For DLM461
1. Open the rear cover, and then remove the grass basket.
► Fig.18: 1. Rear cover 2. Grass basket
2.
Attach the mulching attachment while pulling the
lever, and then release the lever to lock the mulching
attachment.
► Fig.19: 1. Mulching attachment 2. Lever
FUNCTIONAL
DESCRIPTION
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the machine and the battery
cartridge firmly when installing or removing bat-
tery cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
CAUTION:
Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: The tool does not work with only one battery
cartridge.
To install the battery cartridge;
1. Pull up the locking lever, and then open the battery cover.
► Fig.20: 1. Battery cover 2. Locking lever
2.
Align the tongue on the battery cartridge with the
slot on the mower then slide the cartridge until it locks in
place with a little click.
► Fig.21: 1. Battery cartridge
3. Insert the lock key in the place shown in the figure
as far as it will go.
► Fig.22: 1. Lock key
4.
Close the battery cover and push it until it is
latched with the locking lever.
To remove the battery cartridge from the mower;
1. Pull up the battery cover locking lever and open
the battery cover.
2. Pull out the battery cartridge from the mower while
sliding the button on the front of the cartridge.
3.
Pull out the lock key.
4. Close the battery cover.
13 ENGLISH