BTI PROFILINE A-SBS 36V LI Manual Original página 31

OBJ_BUCH-888-001.book Page 31 Thursday, February 19, 2009 12:55 PM
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as: main-
tain the tool and the accessories, keep the hands
warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the
product described under "Technical Data" is in con-
formity with the following standards or standardization
documents: EN 60745 according to the provisions of
the directives 2004/108/EC,
28 Dec 2009), 2006/42/EC (from 29 Dec 2009).
Technical file at:
BTI Befestigungstechnik GmbH
D-74653 Ingelfingen
Jürgen Dietz i. V. Günter Hub
General Manager Purchasing Manager
31.10.2008, BTI Befestigungstechnik GmbH
74653 Ingelfingen
Assembly
Battery Charging
Use only the battery chargers listed on the
accessories page. Only these battery chargers
are matched to the lithium ion battery of your
power tool.
Note: The battery is supplied partially charged. To
ensure full capacity of the battery, completely charge
the battery in the battery charger before using your
power tool for the first time.
The lithium ion battery can be charged at any time
without reducing its service life. Interrupting the
charging procedure does not damage the battery.
The Li-ion battery is protected against deep discharg-
ing by the "Electronic Cell Protection (ECP)". When
the battery is empty, the machine is switched off by
means of a protective circuit: The inserted tool no
longer rotates.
2 609 932 668 • 19.2.09
WARNING
machine has been automatically switched off.
The battery can be damaged.
Removing the Battery
The battery 8 is equipped with two locking levels that
should prevent the battery from falling out when push-
ing the battery unlocking button 13 unintentionally. As
long as the battery is inserted in the power tool, it is
held in position by means of a spring.
98/37/EC (until
To remove the battery 8:
– Push the battery against the base of the power tool
(1.) and at the same time press the battery unlock-
ing button 13 (2.).
– Pull the battery out of the power tool until a red
stripe becomes visible (3.).
– Press the battery unlocking button 13 again and
pull out the battery completely.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indi-
cator 11 indicate the charge condition of the battery 8. For
safety reasons, it is only possible to check the status of
the charge condition when the machine is at a standstill.
Push button 12 to indicate the charge condition (also
possible when the battery is removed). The battery
charge-control indicator automatically goes out after
approx. 5 seconds.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 12, then
the battery is defective and must be replaced.
During the charging procedure, the three green LEDs
light up one after the other and briefly go out. The bat-
tery is fully charged when the three green LEDs light
up continuously. The three LEDs go out again approx.
5 minutes after the battery has been fully charged.
The battery is equipped with a NTC temperature con-
trol which allows charging only within a temperature
range of between 0 °C and 45 °C. A long battery
service life is achieved in this manner.
Do not continue to press the
On/Off switch after
Capacity
≥2/3
≥1/3
<1/3
Reserve
English | 31
the