EINHELL GE-CL 36 Li Solo Manual De Instrucciones Original página 25

5. Before starting the equipment
The equipment is supplied without batteries
and without a charger.
Warning!
Always remove the batteries before making
adjustments to the equipment.
5.1. Mounting the suction tube (Fig. 3a-3f)
•
Plug together the front and rear suction tube
(Fig. 3a) and secure with the screw (Fig. 3b/
Item 12).
•
Now slide the complete suction tube into the
motor housing (Fig. 3c) and secure with the
screws (Fig. 3d/ Item 12).
•
Fit the two wheels (Fig. 3e/Item 9) into the
wheel support (Fig. 3e/ Item 11). Make sure
that there is an audible click when they en-
gage.
•
Slide the wheel support (Fig. 3f/Item 11) onto
the front suction tube as far as the stop (Fig.
3f/Item D) and secure with the screw (Fig. 3f/
Item 13).
Note: Please note that the two vacuum tubes
must always be joined together before they
are mounted on the motor housing, and that
they must never be taken apart when moun-
ted!
5.2. Mounting the catch bag (Figs. 4-5)
Hang the hook on the suction tube (Fig. 4A) and
on the housing (Fig. 4b). Then slip the catch bag
over the socket on the motor housing; it engages
correctly when it makes an audible click (Fig. 5).
5.3. Fitting the handle
Slide the handle (Fig. 6a/Item A) onto the mounts
in the housing as far as the stop. Then fasten the
handle on both sides with one screw on each side
(Fig. 6b/Item 13).
5.4. Fitting the additional handle
Remove the star screw (Fig. 7/Item B), fi t the
handle (Fig. 7/Item 3) to the mount and secure the
handle in the required position with the star screw.
5.5. Fitting the harness
Open the knurled screw (Fig. 8/Item C), feed the
belt strap (Fig. 8/Item 4) through the opening and
close the knurled screw again.
5.6 Fitting the battery (Fig. 9)
Anl_SA_GE_CL_36_Li_E_Solo_SPK8.indb 25 Anl_SA_GE_CL_36_Li_E_Solo_SPK8.indb 25
GB
Press the pushlock button (Fig. 9/Item E) of the
battery as shown in Fig. 9 and push the battery
into the battery mount provided. When the bat-
tery is positioned as in Fig. 9, make sure that the
pushlock button latches in place! To remove the
battery pack, proceed in reverse order.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two batte-
ries must always be fully charged before use.
5.7 Charging the battery
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger.
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless leaf blower
drops. Never allow the battery pack to become
fully discharged. This will cause it to develop a
defect.
Start up the equipment only when fully assem-
bled.
- 25 -
24.08.2017 10:14:31 24.08.2017 10:14:31