Important Safety Instructions For All Battery Packs - DeWalt DC608 Manual De Instrucciones

Ocultar thumbs Ver también para DC608:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

• Keep face and body parts away from back of the tool cap
when working in restricted areas. Sudden recoil can result
in impact to the body, especially when nailing into hard or dense
material. (Fig. J)
• Grip tool firmly to maintain control while allowing tool to
recoil away from work surface as fastener is driven. In Bump
mode, if contact trip is allowed to recontact work surface before
trigger is released, an unwanted fastener will be fired.
• Choice of triggering method is important. Check the manual
for triggering options.
BUMP/SEQUENTIAL SELECTOR SWITCH
Sequential Action
(Fig. K)
• When using the tool in sequential action, do not actuate
the tool unless the tool is placed firmly against the
workpiece.
Bump Action
(Fig. L)
• When using the tool in bump action, be careful of unin-
tentional double fires resulting from tool recoil. Unwanted
fasteners may be driven if the contact trip is allowed to accidentally
re-contact the work surface.
TO AVOID DOUBLE FIRES:
• Do not engage the tool against the work surface with a
strong force.
• Allow the tool to recoil fully after each actuation.
• Use sequential action trigger.
• When "bump" actuating the brad nailer, always keep tool in control. Inaccurate
placement of tool can result in misdirected discharge of a fastener.
• Do not drive nails onto the heads of other fasteners. Strong recoil, jammed fasteners,
or ricocheted nails may result. (Fig. M)
• Be aware of material thickness when using nailer. A protruding nail may cause injury.
• DEPTH ADJUSTMENT: To reduce risk of serious injury from accidental actuation
when attempting to adjust depth, ALWAYS;
• Remove battery pack.
• Engage contact trip lock-off (Fig. N).
• Avoid contact with trigger during adjustments
• Do not drive nails blindly into walls, floors or other work areas. Fasteners driven into
live electrical wires, plumbing, or other types of obstructions can result in injury. (Fig. O)
• Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating power tools may result in serious
personal injury.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or
long hair can be caught in moving parts.
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
FIG. M
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
FIG. N
microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin
may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disperse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
FIG. O
WARNING: Always wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
CAUTION: When not in use, place tool on its side on a stable surface where it
will not cause a tripping or falling hazard. Some tools with large battery packs will stand
upright on the battery pack but may be easily knocked over.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V .....................volts
Hz ...................hertz
min .................minutes
or DC .....direct current
...................Class I Construction
.......................(grounded)
...................Class II Construction
.../min ............per minute
IPM .................impacts per minute
SPM ...............strokes per minute

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and voltage.
Consult the chart at the end of this manual for compatibility of chargers and battery packs.
The battery pack is not fully charged out of the carton. Before using the battery pack and
charger, read the safety instructions below. Then follow charging procedures outlined.
• Do not charge or use battery in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Inserting or removing the battery from the charger
may ignite the dust or fumes.
• NEVER force battery pack into charger. DO NOT modify battery pack in any way
to fit into a non-compatible charger as battery pack may rupture causing serious
personal injury. Consult the chart at the end of this manual for compatibility of batteries
and chargers.
4
A .........................amperes
W ........................watts
or AC .............alternating current
or AC/DC......alternating or direct current
n o .......................no load speed
n .........................rated speed
.......................earthing terminal
(double insulated)
........................safety alert symbol
BPM ...................beats per minute
RPM ...................revolutions per minute
sfpm ...................surface feet per minute
READ ALL INSTRUCTIONS

Publicidad

Tabla de contenido
loading

Tabla de contenido