Flotec FP0S1800A Manual Del Usuario página 2

Specifications and Safety
DESCRIPTION
This Submersible Sump Pump is designed for home
sumps. Unit is equipped with a 3-prong grounding-type
power cord. Shaded-pole motor is oil filled and sealed
for cooler running. Sleeve bearings on motor shaft never
need lubrication. Automatic reset thermal protection. Not
designed for use as a swimming pool drainer.
SPECIFICATIONS
Power supply required ...........................115V, 60 HZ.
Liquid Temp. Range ................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required (min.) ....15 Amps
Discharge:
Plastic Models............1-1/4" FNPT / 1-1/2" MNPT
Cast Iron Models ...............................1-1/2" FNPT
NOTICE: Do not reduce size of discharge pipe or
hose below 1-1/4" diameter. If discharge is too
small, pump will overheat and fail prematurely.
NOTICE: This unit is not designed for applications
involving salt water or brine! Use with salt water or
brine will void warranty.
Pump water only with this pump.
Do not use where water recirculates.
Not designed for use as a swimming pool
drainer.
PERFORMANCE
GPH (LPH) AT TOTAL FEET (M) OF LIFT
Motor
Series HP (1.5m)
CAPACITY GALLONS(L)/HOUR
FP0S1800A
1/4
FP0S1800LTS (8 631)
FP0S2400A
1/3
FP0S2450A (10 448) (8 176)
FP0S3200A
1/2
FP0S3250A (12 113) (10 220) (7 571)
FPSC2200A
1/3
FPSC2250A (10 599)
ELECTRICAL & SWITCH SPECIFICATIONS
Motor
Motor Full Load
Series HP Amps
FP0S1800A 1/4 8.5
FP0S1800LTS 1/4 8.5
FP0S2400A 1/3 9.0
FP0S3200A 1/2 5.5
FPSC2200A 1/3 9.0
FP0S2450A 1/3 9.0
FP0S3250A 1/2 5.5
FPSC2250A 1/3 9.0
For parts or assistance, call Flotec Customer Service at
5 10 15
(3m) (4.6m)
2280 1620 660
(6 132) (2 498)
2760 2160 1410
(5 337)
3200 2700 2000
2800 2200 1400
(8328) (5299)
Individual
Branch *Switch Setting
Circuit in inches (mm)
Req.(Amps) On
15 11 3 ⁄ "(298) 4
4
15 6 1 ⁄ "(159)
4
15 13"(330)
15 13"(330)
15 13"(330)
15 8"(203)
15 8"(203)
15 8"(203)
GENERAL SAFETY INFORMATION
Electrically powered sump pumps normally give
many years of trouble-free service when correctly
installed, maintained, and used. However, unusual
circumstances (interruption of power to the pump,
dirt/debris in the sump, flooding that exceeds the
pump's capacity, electrical or mechanical failure in
the pump, etc.) may prevent your pump from func-
tioning normally. To prevent possible water damage
due to flooding, consult your retailer about a sec-
ondary AC sump pump, a DC backup sump pump,
and/or a high water alarm. See the "Troubleshooting
Chart" in this manual for information about common
sump pump problems and remedies. For more infor-
mation, see your retailer, call Flotec customer
service at 1-800-365-6832 or visit our website at
www.flotecwater.com.
1. Know the pump application, limitations, and
potential hazards.
2. Do not use in water with fish present.
3. Disconnect power before servicing.
4. Release all pressure within system before servic-
ing any component.
5. Drain all water from system before servicing.
6. Secure discharge line before starting pump. An
unsecured discharge line will whip, possibly
causing personal injury and/or property damage.
7. Check hoses for weak or worn condition before
each use, making certain that all connections are
No flow
secure.
at height
shown
8. Periodically inspect sump, pump and system
below
components. Keep free of debris and foreign
18 Ft.
objects. Perform routine maintenance as
(5.5M)
required.
20 Ft.
9. Provide means of pressure relief for pumps whose
(6.1M)
discharge line can be shut-off or obstructed.
24 Ft.
10. Personal Safety:
(7.3M)
20 Ft.
a. Wear safety glasses at all times when working
(6.1M)
with pumps.
b. Keep work area clean, uncluttered and prop-
erly lighted – replace all unused tools and
equipment.
c. Keep visitors at a safe distance from work
area.
d. Make workshop child-proof – with padlocks,
master switches, and by removing starter
Off
1 ⁄ "(114)
keys.
2
3"(76)
11. When wiring an electrically driven pump, follow
6"(152)
all electrical and safety codes that apply.
6"(152)
12. This equipment is only for use on 115 volt (sin-
6"(152)
4"(102)
gle phase) and is equipped with an approved
4"(102)
3-conductor cord and 3-prong, grounding-type
4"(102)
plug.
1-800-365-6832
2