Polar Refrigeration G603 Manual De Instrucciones página 8

UK
To unlock the control panel:
Press and hold the UP and DOWN
1.
Pon flashes on the display and the keyboard is unlocked.
2.
Note:
If a button is not pressed for 10 seconds while using the control panel it times out and reverts to standby mode.
When parameters are being set the Setpoint LED will flash on the display.
Enter the Parameter Menu
Unlock the control panel, if locked.
1.
Press and hold the SET
2.
If necessary, press the SET
3.
Alter Parameter Value
Note: Your POLAR appliance has been preset with default parameters generally deemed suitable for normal operation. POLAR
recommend these preset values are used.
To alter the value, (if necessary):
With the desired parameter displayed, alter the value using the UP
1.
Press the SET button to store the value.
2.
Note: The control panel will automatically move to the next parameter. To return to standby mode allow the control panel to time
out.
Parameter Descriptions
Parameter Name
Operating
d1
temperature
Temperature
d2
Differential
d3
Temperature Range
d4
Compressor Activation
d5
Time Intervals
Maximum
d6 Temperature
Differential Alarm
Temperature
d7 Differential Alarm
Delay
Defrost Cycle Time
d8
Intervals
Maximum Defrost
d9
Duration
Defrost Cut-off
d10
Temperature
Additional Cut-off
d11
Defrost Period
Delayed Actual
d12
Temperature Display
Compressor On/Off
d13
During Defrost
Evaporator Drying
d14
Time
=19 Temperature Offset
=22 Unit of Measurement
3
buttons simultaneously for 10 seconds.
button until 'd1' flashes on the display.
button repeatedly to scroll to the desired parameter (see "Parameter Descriptions" for parameter details).
Set the operating temperature of the appliance
The Temperature Differential is the allowed temperature difference above and
below the operating temperature before the compressor starts/cuts off
Set the minimum (d3) and maximum (d4) temperatures that the appliance
can fluctuate between
Enter the minimum time interval between the compressor turning off after
turning on.
Set an alarm to sound if the temperature inside the appliance exceeds the set
operating temperature by a specified amount
Set a delay before the temperature differential alarm is triggered
Set the time between each defrost cycle
Set the maximum length of the defrost cycle
Note: The defrost duration can be overridden by parameter d10
(below), if the cut-off temperature is reached before the end of the
defrost duration
Set the defrost cut-off temperature
Set an additional amount of defrost time after the defrost cut-off point has been
reached (if required)
Set the length of time the inner temperature of the appliance (before defrost
started) is displayed for after a defrost cycle has finished
Turn the Compressor On or Off during the defrost cycle
Set the amount of time the compressor remains turned Off after a defrost
cycle, reducing the amount of frost build up
Should there be any variance between measured and actual temperature, the
measured temperature can be offset to compensate
Set whether the temperature is displayed in Centigrade or Fahrenheit
and DOWN buttons.
Description
Default Parameter Value
Range
Base
-2°C to 10°C 2°C
0 to 20°C 2°C
-40°C 2°C
95°C 10°C
0-999 seconds 99
0°C-50°C 50°C
0-99 minutes 0
1-999 hours 6
0-999 minutes 30
-45°C to 50°C n/a
0-99 minutes n/a
0-99 minutes 30
On (1) or Off (0) n/a
0-99 minutes 0
-20°C to 20°C -3°C
Centigrade (0) or
0
Fahrenheit (1)
Top
2°C
2°C
0°C
10°C
99
50
0
24
1
n/a
n/a
0
n/a
0
-5°C
0