Publicidad
Idiomas disponibles
Idiomas disponibles
English
-
Sanding should be done in a manner to reduce
tracking of paint dust outside the work area.
3. ClEAning AnD DisPOsAl
-
All surfaces in the work area should be vacuumed
and thoroughly cleaned daily for the duration of
the sanding project. Vacuum filter bags should be
changed frequently.
-
Plastic drop cloths should be gathered up and
disposed of along with any dust chips or other
removal debris. They should be placed in sealed
refuse receptacles and disposed of through regular
trash pick-up procedures. During clean up, children
and pregnant women should be kept away from the
immediate work area.
-
All toys, washable furniture and utensils used by
children should be washed thoroughly before being
used again.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Replacing the Sanding Pad and the Belt
(Fig. H)
Your sander is equipped with a replaceable belt
is located between the pad
6
It is designed to control the pad speed while the unit is
off the work surface. The belt and the sanding pad
designed to be consumable parts and will occasionally need
to be replaced. The sanding pad needs replacement when
signs of wear become evident. Replacement of the belt is
necessary when the pad speed increases very dramatically
when the unit is lifted from the work surface. These parts are
available at extra cost from your local dealer or authorized
D
WALT service center.
e
1. Holding the platen firmly, remove the four screws
from the bottom of the pad.
2. Remove the pad
.
6
3. Replace worn or damaged belt
around the shoulder screw
as shown in Figure H.
4. Reinstall pad (replace with new pad if necessary).
Replace the four screws
13
tighten screws.
10
10
which
and the sander body
.
12
6
are
13
by wrapping it
10
14
and bearing retainer
15
. Be careful not to over-
Fig. H
11
12
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Accessories
WARNING: Since accessories, other than those
offered by D
WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D
WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.
Repairs
The charger and battery pack are not serviceable.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement, when
applicable) should be performed by a D
service center or a D
WALT authorized service center.
e
Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
•
WARRAnTY sERViCE: Registering your product will
help you obtain more efficient warranty service in case
there is a problem with your product.
COnFiRMATiOn OF OWnERshiP: In case of
•
an insurance loss, such as fire, flood or theft, your
13
6
14
10
15
WALT
e
WALT Industrial
e
WALT factory
e
Publicidad
