Publicidad
Idiomas disponibles
Idiomas disponibles
to mow your lawn at the set time on the res-
pective day. It is recommended to base the
mowing time setting on 8 hours per day for
500 m² as a guideline. The selected working
time may need to be adapted to take account
of the garden's size and complexity.
•
Zone
Where gardens have lots of angles, the robot
lawn mower may have problems reaching
every part of the lawn and mowing it comple-
tely. In this case you can select several star-
ting points on the perimeter wire (18). This will
enable the robot lawn mower to get to even
those parts of your garden that are difficult to
reach. The robot lawn mower will run the se-
lected distance along the perimeter wire (18)
and then start mowing in this part of the gar-
den (Fig. 6m). Use the navigation buttons (55)
to go to the point that you wish to change and
enter the distance and frequency accordingly.
The charging station (19) is automatically
defined as starting point 1. The two other st-
arting points can be selected as you wish. For
this you must measure the distance between
the charging station (19) and the starting
point in clockwise direction along the perime-
ter wire (18). With the frequency setting you
decide how often the robot lawn mower starts
its work from the charging station (19) or from
the respective starting points.
•
Boundary cut
Once a week the robot lawn mower will mow
the edge of the lawn at the beginning of its
work window before it starts the mowing ope-
ration. The default factory setting is "On".
•
Error log
From here you will be informed about the
latest error messages concerning your robot
lawn mower.
•
Rain sensor
The rain sensor (5) can be switched on and
off with this setting. The default factory setting
for this sensor is "On". A detailed description
of the rain sensor can be found in the section
"Starting up" under "Sensors".
•
General
- PIN code: You can replace the default
PIN for the robot lawn mower with your own
choice of PIN. To do so, proceed as described
in the chapter "Locking mechanism / PIN". Im-
portant! Make a note of the new PIN.
- Date & time: Use the navigation buttons
(55) to go to the point that you want to change
and make the settings accordingly.
•
Anl_FREELEXO_LCD_BT_plus_SPK9.indb 41
Anl_FREELEXO_LCD_BT_plus_SPK9.indb 41
GB
- Language: Use the navigation buttons (55)
to activate the language that you want.
- Software version: The current version of
the robot lawn mower software is noted here.
Mowing programs – "MODE" button (52)
Use the navigation buttons (55) to go to the
mowing program that you want to start. You can
always choose between "Main area" and "Se-
condary area". More details of the two areas can
be found in the section "Before using for the fi rst
time" under "Perimeter wire".
•
Mowing
When you start the robot lawn mower to mow
the lawn, the mower will switch to normal ope-
rating mode with the set time schedule.
•
Boundary cut
Place the robot lawn mower close to the peri-
meter wire (18) or start the mower while it is in
the charging station (19). With its mower unit
activated, the robot lawn mower will follow
the perimeter wire (18) in counter-clockwise
direction until it reaches the rear of the char-
ging station (19). Provided no work window is
active, the robot lawn mower will then return
to the charging station (19).
•
Spot mowing
It may happen that your robot lawn mower
fails to mow some spots sufficiently. Place the
robot lawn mower at the spot in question and
start the mower. The robot lawn mower will
begin to mow the lawn in a spiral pattern until
it collides with an obstacle or the perimeter
wire (18). Provided no work window is active,
the robot lawn mower will then return to the
charging station (19).
•
Back to station
Send your robot lawn mower back to the
charging station (19). The robot lawn mower
will look for the perimeter wire (18) and follow
it counter-clockwise to the charging station
(19). The secondary area option does not
exist in this case.
6.6. Controlling the robot lawn mower
Starting procedure
1. Press the "STOP" button (3) and open the
display cover (25) fully.
2. Unlock the control panel (2).
3. Use the"MODE" button (52) to select the mo-
wing program and the respective work area
you want.
4. Press the "START" button (53).
5. Close the display cover (25).
- 41 -
18.12.2020 09:10:10
18.12.2020 09:10:10
Publicidad
