Publicidad
Idiomas disponibles
Idiomas disponibles
The robot lawn mower will now operate in ac-
cordance with the mowing time setting. During
work time the battery charge level will appear on
the LCD (50). Whenever the battery charge level
drops to 30%, the robot lawn mower will return
automatically to the charging station (19).
Canceling the mowing operation
1. To bring the robot lawn mower to an immedia-
te stop, press the STOP button (3).
2. Open the display cover (25) fully.
3. Unlock the control panel (2).
4. Press the "MODE" button (52) and select
"Back to station" in order to send the robot
lawn mower along the perimeter wire (18) and
back to the charging station (19).
5. Press the "START" button (53).
6. Close the display cover (25).
6.7 Control of the robot lawn mower using
the app
All settings that you can make using the control
panel can also be made using the app. To do
so, fi rst download the Einhell app for robot lawn
mowers to your smart phone. The Einhell app is
available via the following link and QR code:
iOS: http://qr.einhell.com/12e103ce
Android: http://qr.einhell.com/176c0443
Use a Bluetooth connection to connect the robot
lawn mower with your smart phone and follow the
steps shown there.
Instructions concerning the Bluetooth con-
nection:
•
Connect to the robot lawn mower in the Ein-
hell App after you have logged in as user and
registered the unit.
•
In the case of Android units you must get
approval of the location for the Einhell App in
order to use the Bluetooth connection.
Anl_FREELEXO_LCD_BT_plus_SPK9.indb 42
Anl_FREELEXO_LCD_BT_plus_SPK9.indb 42
GB
•
Connect the robot lawn mower only through
the Einhell App on your smart-phone.
•
Use the Einhell app to establish a connection
to the robot lawn mower.
•
The range of a Bluetooth connection is limi-
ted. This means you must stay close to the
robot lawn mower to control it.
•
The robot lawn mower can be connected to
only one smartphone at a time.
•
Disconnect the Bluetooth connection once
you have made all the settings on the robot
lawn mower.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
The equipment must be disconnected from the
power supply (pull out the power plug and switch
off the equipment by the main switch (7) (OFF)
(Fig. 8) prior to performing any cleaning and
maintenance work. Also take the battery (22) out
of the robot lawn mower.
Caution! Wear work gloves!
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
Do not clean the robot lawn mower with run-
ning water, particularly with high-pressure
water.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment.
•
For best results, clean the robot lawn mower
with a brush or rag.
•
Check the freedom of movement of the bla-
des (10) and the blade plate (11)
•
Use cleaning product for metal or very fine
abrasive paper to clean the charging contacts
on the robot lawn mower (1) and the charging
station (19). Clean them in order ensure effici-
ent charging.
7.2 Maintenance
•
Worn or damaged blades (10) and their fas-
tening screws must always be replaced as a
- 42 -
18.12.2020 09:10:11
18.12.2020 09:10:11
Publicidad
