NovoPress ECO203 Instrucciones De Uso página 20

ACO203 / ECO203
If the battery is inserted in the press device while the battery charge is being checked, the last
pressing operation must have been completed at least 1 minute prior to this. Otherwise the display will
EN
be inaccurate.
Pos : 42 /RVT/Kurz bes chr eibung/Ger ät + Akku/Info welc her Akku18V: AC O/ECO202, AC O202XL, AC O/EC O203 @ 1\mod_1435131784732_18.doc x @ 12829 @ 2 @ 1
7.5 ACO203 and battery
Pos : 43 /RVT/Kurz bes chr eibung/Ger ät + Akku/längere Nichtbenutzung/AC O/ECO203 @ 1\mod_1429171612365_18.doc x @ 11397 @ @ 1
Feature of the press device after extended periods out of use or when changing the battery:
If the press device is out of use for approx. 30 seconds or the battery is reinserted, it switches off. No
LED is lit up any longer. Press the start button (1) briefly to start the press device.
Pos : 44 /RVT/Kurz bes chr eibung/Ger ät + Akku/entl adener Akku/ACO102, AC O152, ACO/EC O202, ACO202XL, ACO401, AC O/ECO203 @ 0\mod_1382607696426_18.doc x @ 1532 @ @ 1
Feature of the press device when the battery is empty:
When a pressing operation begins, a check is made to determine whether the battery charge is
sufficient to complete the pressing operation. If this is not the case the device does not start. The
green LED (2) flashes.
If the green LED (2) flashes following a pressing operation, the pressing operation was carried out
correctly. The battery must be recharged prior to the next pressing operation.
Pos : 45 /RVT/Inbetri ebnahme und Betrieb/Ger ät vorberei ten/1b - Quetsc hgefahr Fing er ACO/EC O202, AFP/EF P202, ACO/EC O203 @ 0\mod_1382615737921_18.doc x @ 1546 @ 12 @ 1
8 Commissioning and operation
8.1 Preparing the ACO203 / ECO203
Pos : 46 /RVT/Inbetri ebnahme und Betrieb/Ger ät vorberei ten/3 - Info-H altebolzen ACO/EC O202, ECO301, AC O/ECO203 @ 0\mod_1382617008258_18.doc x @ 1559 @ @ 1
Pos : 47 /RVT/Inbetri ebnahme und Betrieb/Ger ät vorberei ten/4 - Info D auer betrieb ACO102, AC O152, ACO/EC O202, ACO202XL, EC O301, AF P/EFP202 @ 0\mod_1382617729764_18.doc x @ 1565 @ @ 1
Pos : 48 /RVT/Inbetri ebnahme und Betrieb/Ger ät vorberei ten/5b - Ei ns etz en AC O/ECO202, AC O/ECO203 @ 0\mod_1385646619856_18.doc x @ 1596 @ @ 1
Pos : 49 /RVT/Allgemeines /#### Seitenumbr uch #### @ 0\mod_1380200837280_0.doc x @ 885 @ @ 1
Information!
The ACO203 press device must only be operated with 18 V lithium-ion
rechargeable batteries. The 18 V battery must only be used in the appropriate
press devices.
CAUTION!
Fingers risk being crushed if the device is operated without a press
jaw/adaptor jaw (Fig. 4)
If no press jaw/adaptor jaw is fitted, fingers could be placed in the at-risk zone. Fingers
could be crushed when the device is started.
Therefore:
– Do not operate the device without press jaws.
– Keep your fingers away from the at-risk zone.
Information!
The device will not start if the retaining pin (8) is incorrectly inserted. The green LED
flashes.
Information!
The press device is not suitable for continuous operation. Following 30 minutes
of continuous operation, a short break of at least 15 minutes must be taken to
allow the device to cool down.
• Insert the press jaw/adaptor jaw into the press device as shown in Fig. 5 to 7.
16