Publicidad
Idiomas disponibles
Idiomas disponibles
• NEVER use tool without a fully operative switch
trigger. Any tool with an inoperative switch is HIGHLY
DANGEROUS and must be repaired before further
usage or serious personal injury may occur.
• NEVER defeat the lock-off button by taping down
or some other means. A switch with a negated lock-
off button may result in unintentional operation and
serious personal injury.
• NEVER use the tool if it runs when you simply pull
the switch trigger without pressing the lock-off
button. A switch in need of repair may result in
unintentional operation and serious personal injury.
Return tool to a Makita service center for proper repairs
BEFORE further usage.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
A hole is provided in the switch trigger for insertion of a
padlock to lock the tool off.
WARNING:
• Do not use a lock with a shank or cable any smaller
than 6.35 mm in diameter. A smaller shank or cable
may not properly lock the tool in the off position and
unintentional operation may occur resulting in serious
personal injury.
Lighting up the lamps (Fig. 14 & 15)
Only for model LS1040F / LS1040FS
CAUTION:
• This is not a rainproof light. Do not wash the light in
water or use it in a rain or a wet area. Such a conduct
can cause an electric shock and fume.
• Do not touch the lens of the light, as it is very hot while
it is lighted or shortly after it is turned off. This may
cause a burn to a human body.
• Do not apply impact to the light, which may cause
damage or shorted service time to it.
• Do not keep casting the beam of the light to your eyes.
This can cause your eyes to be hurt.
• Do not cover the light with clothes, carton, cardboard or
similar objects while it is lighted, which can cause a fire
or an ignition.
Push the upper position of the switch for turning on the
light and the lower position for off.
Move the light to shift an area of lighting.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of light, or it may lower
the illumination.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing and removing saw blade
CAUTION:
• Always be sure that the tool is switched off and
unplugged before installing or removing the blade.
• Use only the Makita socket wrench provided to install
or remove the blade. Failure to do so may result in
overtightening or insufficient tightening of the hex bolt.
This could cause an injury.
Installing saw blade
NOTE:
• The saw blade may have already been installed at the
time of shipment.
To install the blade, do the following steps.
1.
Keep the handle in the raised position.
2.
Use the socket wrench to loosen the hex bolt
holding
the
center
counterclockwise. Then, raise the blade guard and
center cover. (Fig. 16)
3.
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt clockwise.
Then remove the hex bolt and outer flange. (Fig. 17)
4.
Mount the saw blade carefully onto the spindle,
making sure that the direction of the arrow on the
surface of the blade matches the direction of the
arrow on the blade case. (Fig. 18)
5.
Install the flange and hex bolt, and then use the
socket wrench to tighten the hex bolt (left-handed)
securely counterclockwise while pressing the shaft
lock. (Fig. 19)
CAUTION:
• The ring 25.4 mm or 30 mm in outer diameter is
factory-installed onto the spindle. Before mounting
the blade onto the spindle, always be sure that the
correct ring for the arbor hole of the blade you
intend to use is installed onto the spindle.
6.
Return the blade guard and center cover to its
original position. Then tighten the hex bolt clockwise
to secure the center cover.
7.
Lower the handle to make sure that the blade guard
moves properly.
8.
Make sure shaft lock has released spindle before
making cut.
Removing saw blade
1.
Keep the handle in the raised position.
2.
Use the socket wrench to loosen the hex bolt
holding
the
center
counterclockwise. Then, raise the blade guard and
center cover.
3.
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt clockwise.
Then remove the hex bolt, outer flange and blade.
When storing the tool, install the outer flange and lightly
tighten the hex bolt by hand to prevent loss.
Connecting a vacuum cleaner (Fig. 20)
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner.
Dust bag (Fig. 21)
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove
particles adhering to the insides which might hamper
further collection.
cover
by
turning
cover
by
turning
17
it
it
Publicidad
