Working With The Machine; Maintenance And Repairs - Solo 142 Manual De Instrucciones

Ocultar thumbs Ver también para 142:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 62
Safety regulations

1.7 Working with the machine

Only use this power tool when it is complete and in a safe condition.
As soon as the engine is running, the power tool generates toxic gases, which may be invisible and
odourless. Never work with the power tool in enclosed spaces. In confined conditions such pits or
excavations, ensure adequate air changes during work.
Do not smoke at the work site and in the immediate vicinity of the power tool. There is an increased fire
hazard!
Work conscientiously, thoughtfully and calmly, and do not endanger third parties.
- Pay attention to good visibility and lighting conditions.
- Always remain within earshot of other people who can provide help in case of emergency.
- Plan for timely work breaks.
- Pay attention to possible hazards and take appropriate precautions. Be aware that wearing ear defenders
reduces the ability to perceive noise. This includes sounds alerting to danger such as signals, shouts, etc.
that can go unnoticed.
- Exercise caution when the ground is wet or covered in ice and snow, on overhangs, or uneven terrain.
There is an increased risk of slipping!
- Pay attention to the risk of stumbling and obstacles, such as tree roots and stumps, edges, etc. Pay
particular attention to safety when working on slopes.
- Before commencing work, check the working area for stones, broken glass, nails, wire or other solid
objects and remove such debris to prevent them being picked up and thrown out by the cutters.
- Always hold this power tool firmly in both hands, and ensure your safe and solid foothold.
- Always hold the cutters below hip level. Never lift a rotating cutter off the ground.
- Keep all parts of the body away from rotating cutters.
- Use a correct operating mode (see Chapter 8.3 "Correct brushcutter operation").
- Use the power tool at lowest possible noise and exhaust levels. Only open the throttle when working, do
not let the engine run unnecessarily. Please note that noise also impacts on the environment. Observe
the quiet times that can vary from place to place.
- Never use blunt cutters and avoid uncontrolled contact of the cutter with debris. Otherwise there will be an
increased risk of the equipment kicking, which could throw the entire machine around. As a result, the
operator could be subjected to involuntary movements, which could lead to serious injury or death.
Stop the engine if you notice a difference in the operating characteristics of the brushcutter.
Due to the centrifugal clutch, the cutters will run on for a short time, even if you release the throttle. Ensure
the cutter has come to a full stop before storing the machine.
Always stop the engine before any contact with the cutter – even when clearing a blockage or if cutters
have become jammed – wait until the cutter has stopped and remove the spark plug cap.
Never touch the exhaust or the silencer; as long as they are still hot, there is a risk of burns!
Never work with a defective or missing silencer. There is a hazard of hearing damage and burning!
First Aid
A first aid box should always be available on-site. Immediately replace any materials you have used:
Note:
Over exposing persons with circulatory problems to vibrations can lead to damage to their nervous system or
blood vessels. The following systems may occur from vibrations to fingers, hands or the wrists: Numbness,
itching, pain, twinges, changes to the colour of the skin or the skin itself. Seek medical advice if you experience
any of these symptoms.

1.8 Maintenance and repairs

Regularly service this machine. Only carry out those maintenance jobs and repairs, which are described in this
manual. A specialised service centre will carry our all other jobs.
Do not maintain, repair or store the machine near an open flame.
Before cleaning, maintenance and repair work, always stop the engine first and pull the spark plug cap.
Exceptions: carburettor and idle adjustments.
For any repairs only use original parts from the manufacturer.
Do not modify, alter or change the machine as this may impact on the safe operation of the machine and
may lead to accidents and injuries!
ENGLISH 6

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

154

Tabla de contenido