Peg-Perego TAURUS Empleo Y Manutencion página 12

MAINTENANCE AND VEHICLE
CARE
• Do not disassemble or try to repair the vehicle on
your own. Contact an authorised Peg Perego
customer support centre.
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used.
• Always disconnect the battery charger from the
toy before carrying out cleaning, maintenance, or
any type of intervention.
• For repairs use only original PEG PEREGO spare
parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
CUSTOMER SERVICE
PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
Refer to the last illustration in this manual to find
the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Connect the 2 parts of the left handle (SX). The
letters "DX" and "SX" on the back of each
component indicate the right- and the left-hand
side, respectively. Use the screw provided to
tighten them in place.
2 • Place the handle on the left-hand side of the seat
and tighten it using the 3 screws provided.
Repeat these operations for the remaining
handle.
3 • Insert the mirror stem in its housing, as shown in
the figure, position the retainer clamp, and
tighten it into place using the 2 screws provided.
4 • Complete the mirror assembly by pressing the
toy mirror (1) and its frame (2) into place.
Repeat these operations for the other mirror.
5 • Turn the vehicle upside down. Slightly lift the 2
steering levers, rotating them until they engage
with the steering bar.
6 • Fasten the 2 steering levers using the respective
screws.
7 • Snap the gear lever into place.
8 • Place the seat, aligning it with the holes according
to the child's height. The vehicle has 4 positions
(see diagram). IMPORTANT! Slide the caisson
back to place the seat in position four. Refer to
figures 52 to 58 for this operation.
9 • Fasten the seat from underneath, using the 4
knobs.
10 •Insert the steering column tube, as shown in the
figure.
11 •Bring the dashboard closer to the chassis and
connect the dashboard cable to the vehicle's
electrical system, as shown in the figure.
12 •Insert the dashboard, aligning it with the 3 front
bonnet housings and the steering column's hole.
13 •Place the left side panel next to the dashboard.
14 •Secure it to the chassis by snapping the 3 hooks
into place. Repeat these operations for the other
side panel.
15 •Install the crossbar between the 2 side panels.
16 •Install the roll bar over the crossbar.
17 •Tighten it using the 4 screws provided (2 per
side), as shown in the figure.
18 •Install the left mirror by inserting the lower part
first (1) and then the upper part (2), as shown in
the figure.
19 •Tighten it using the 2 respective screws. Repeat
these operations for the remaining mirror.
20 •Connect the steering wheel cable to the
dashboard cable. IMPORTANT! Place the cables
in their housing to prevent them from getting
crushed. Mount the steering wheel on the
steering column, aligning the respective holes to
keep it in place.
21 •Fasten the steering wheel using the screw and
bolt provided, inserting the screw into the round
hole and the bolt into the hexagonal hole.
22 •Press the 2 front shock absorbers into the slots,
as shown in the figure.
23 •Remove the 2 plastic protectors from the rear
axle. Insert the axle into the chassis.
24 •Fit the rear wheels (the wider ones) onto the
axle, keeping the rims on the outside.
25 •Insert 1 small metal washer and 1 nut on each
side. If the axle comes out of the wheels, insert a
plastic washer after the wheel. Make sure to
insert it in the right direction, as shown in detail
A.
26 •Fasten the wheels simultaneously using the 2 keys
provided.
27 •Fit 1 large metal washer to the steering lever.
28 •Fit the front wheel, 1 small metal washer and 1
nut.
29 •Tighten the wheel using the key provided. Repeat
these operations for the remaining wheel.
30 •Press the 4 hubcaps into place.
31 •Snap the 2 inserts into place on the front
bumper.
32 • Join the 2 parts of the winch.
33 •Place the winch on the bumper.
34 •Tighten it from the back using the 4 screws
provided.
35 •Remove the 4 front plastic protectors from the
chassis. Fit the bumper you just assembled to the
chassis.
36 •Fasten it using the 4 screws provided.
37 •Divide the two handles (use scissors if necessary)
and remove the two pieces of plastic joining
them.
38 •Loosen the two screws on the caisson (as shown
in the figure). Remove the plastic bushing. Keep
the screws for later. You'll need them to fasten
the handles.
39 •Snap the handles into place, as shown in the
figure.
40 •Now fasten them using the screws you put aside
a moment ago.
41 •Place the caisson upside down and snap the rear
mudguards into place, making sure to place them
in the right direction, as shown in the figure.
42 •Place the caisson, aligning it with the holes (see
the detail in the figure).
43 •Lock the caisson in the rear part by inserting the
two pins shown in the figure until the lock snaps
into place.
44 •Right pin positioned correctly.
45 •Join the spring and the red lock as shown in the
figure. Lift the piston and insert the red hook in
the upper part, as shown in the figure.
46 •Keep the piston lifted. Align its hole with the
caisson's rear hole (as shown in the figure).
47 •Lock it in place with the pin.
48 •Ensure that the pin is inserted all the way down,
like in the figure. Now press the caisson down.
49 •Open the battery compartment by turning the
red hook to the "open lock" position, helping
yourself with a coin.
50 •Connect the battery plug to that of the electrical
system. Put the battery compartment cover back
into place. Then, turn the red hook by 180
degrees to close it. The vehicle is ready for use.
FEATURES AND INSTRUCTIONS
FOR USE
51 •A: START button to activate all the dashboard
functions (lights, beacon, horn)
- B: horn
- C: storage compartment/cup holder
- D: grab handle
- E: beacon that turns on when the vehicle is
moving, paired with a beeper only in reverse gear.
- F: front lights
- G: manual winch
52 •The caisson has a backboard, which you can open
by pushing the two red levers on the sides
upwards.
52 •The tip-up caisson can hold loads up to 10 kg. To
tilt it, pull up the tie rod to release it, as shown in
the figure, and simultaneously, lift the caisson
using the handles on the sides.
53 •The tip-up caisson can hold loads up to 10 kg. To
tilt it, pull up the tie rod to release it, as shown in
the figure, and simultaneously, lift the caisson
using the handles on the sides.
54 •Remove the three fixing pins to move the caisson
backwards by one position. To do so, unlock the
pins by pressing on the tabs with a tool and
remove the caisson.
55 •Remove the two oval pins from their joints,
breaking the connecting parts.
56 •Insert the joints into their housing at the bottom
of the vehicle.
57 •Tighten them into place using the pins you
removed earlier.
58 •Place the caisson back onto the vehicle.
59 •Align the caisson's rear holes with the ones on
the joints. Fasten the caisson using the two oval
pins you removed earlier from the joints.
60 •Use the last pin to fasten the piston in the first
front hole on the caisson. Always ensure the pins