Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Bedienungsanleitung / Operating Instructions / Instructions de service / Instrucciones de manejo
Elektromagnetventile / Solenoid Valves /
Electrovanne / Válvulas electromagnéticas
30.30.01.00067
EN
Technical data
Nominal diameter
Nominal flow [m³/h]
Connection
Weight [kg]
Switch function
Pilot control pressure
Body material
Power consumption
DC 24 V
AC 110 V
AC 230 V
Vacuum / Pressure range
Enclosure type
Media
Pressure connection
Direction of flow
Orientation
Operating Temperature
Pressure media
Rated voltage
Drive
Duty cycle
* with auxiliary manual actuation
Instructions for valves
The solenoid valves have sliding bearings which require no maintenance. Nevertheless, we recommend that you
include the valves in the normal regular maintenance of the plant. Depending on the operating conditions and the
inspection intervals, dirt may be deposited in the valve or wear of parts (seals, diaphragms, piston rings, spindles,
etc.) may occur. Attention should be paid to the type-specific installation parameters such as the direction of flow,
installation orientation, operating pressure, electrical and air-line connections. In order to ensure trouble-free
operation of the valves, the following points should be observed.
Installation
Before installing the valve, ensure that the piping is absolutely clean in order to prevent dirt from entering the valve.
Compare the values on the rating plate and in the data sheet with the actual operating values to ensure that the rated
values are not exceeded.
A dirt trap installed before the valve will improve the operational reliability and prevent blocking of the control lines in
the valve.
Ensure that the pipes in which the valve is to be fitted are correctly aligned and laid in accordance with the planning
drawings. Avoid undue stress on the valve body which could result from the use of unsuitable tools
and/or sealing materials. Use only tools of the correct size on the connection fittings. The piping should be laid such
that there is no transmission of force through the longitudinal axis of the valve.
The electrical connections are made with the appropriate plug connector. Before connecting, ensure that the
actual voltage matches the value specified on the rating plate. Observe the markings on the terminals, since incorrect
connection of the voltage can result in destruction of the valve.
Ensure that the valve is correctly grounded in order to prevent electric shocks.
The electrical operation of the valve should be tested before the medium is connected. The valve must click audibly
when the switching voltage is applied. Do not attempt to strip the valve while the voltage is present: this is dangerous
and will result in major damage in the case of AC solenoids.
The warranty becomes invalid of the installation instructions are not observed!
Always specify the valve type and the supply voltage in any inquiries.
Status 07.2020 / Index 02
EMVP 10
EMVP 15* EMVP 19* EMVP 25* EMVP 39
10 mm
15 mm
10
20
3/8"
1/2"
0,93
1,62
NO
NO
3 to 6 bar / 88,6 to 177,2 inHg
medium : -5°C to 60°C ; environment: -5°C to 45°C
medium : 23°F to 140°F ; environment: 23°F to 113°F
DC: 24 V
DC: solenoid AC: solenoid with integrated rectifier
EMVP 10-50
Seite: 3 / 8
19 mm
25 mm
39 mm
35
90
180
3/4"
1"
1 1/2"
1,61
2,14
3,12
NO
NO
NO
Aluminium
11 W
10 – 16 VA
10 - 16 VA
-1 to 0 bar / -29,5 inHg to 0 inHg
IP 65
filtered air
1/8"
as marked
any
filtered and oiled air
AC: 110 V / 50-60 Hz
100% ED
J. Schmalz GmbH
Johannes-Schmalz-Str. 1
D - 72293 Glatten
Tel +49 (0) 7443 / 2403 - 0
www.schmalz.com
schmalz@schmalz.de
EMVP 32
EMVP 32
32 mm
32 mm
130
130
1 1/4"
1 1/4"
0,5
0,5
NO
NC
4 to 7 bar
PVC
5 W
-
5 VA
AC:230 V / 50-60 Hz
EMVP 50
50 mm
310
2"
1,36
NO
Publicidad
Tabla de contenido
