JVC KD-X262 Manual De Instrucciones página 15

AUDIO SETTINGS
Other settings
1 Press and hold .
2 Perform 'Select an item (page 3 or 4)' operation to select an
item (see the following table).
3
Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4
Press to exit.
To return to the previous setting item, press
[EQ SETTING]
[PRESET EQ] Selects a preset equalizer suitable to the music genre.
• Select [USER] to use the settings made in [EASY EQ] or [PRO EQ].
[FLAT]/[DRVN 3]/[DRVN 2]/[DRVN 1]/[HARD ROCK]/[HIP HOP]/
[JAZZ]/[POP]/[R&B]/[TALK]/[USER]/[VOCAL BOOST]/[BASS BOOST]/
[CLASSICAL]/[DANCE]
[EASY EQ] Adjusts your own sound settings.
• The settings are stored to [USER] in [PRESET EQ].
• The settings made may affect the current settings of [PRO EQ].
[SUB.W SP]*1*2: [00] to [+06]
[SUB.W]*1*3: [–08] to [+08]
[BASS]: [LVL–06] to [LVL+06]
[MID]: [LVL–06] to [LVL+06]
[TRE]: [LVL–06] to [LVL+06]
[PRO EQ]
.
Default: [XX]
[AUDIO CONTROL]
[BASS BOOST] [LEVEL +01] to [LEVEL +05] ([LEVEL +01]): Selects your preferred bass boost
(Default: [+03]
[LOUDNESS]
[00]
[LVL 00]
[LVL 00]
[SUB.W
[LVL 00])
LEVEL]*1
*1, *2, *3: (page 12)
Adjusts your own sound settings.
• The settings are stored to [USER] in [PRESET EQ].
• The settings made may affect the current settings of [EASY EQ].
1 [BASS]/[MIDDLE]/[TREBLE]: Select a sound tone.
2 Adjust the sound elements of the selected sound tone.
[BASS] Frequency : [60HZ]/[80HZ]/[100HZ]/[200HZ]
Level : [LVL–06] to [LVL+06]
Q : [Q1.0]/[Q1.25]/[Q1.5]/[Q2.0]
(Default : [80HZ]/[LVL 00]/[Q1.0])
[MIDDLE] Frequency : [0.5KHZ]/[1.0KHZ]/[1.5KHZ]/[2.5KHZ]
Level : [LVL–06] to [LVL+06]
Q : [Q0.75]/[Q1.0]/[Q1.25]
(Default : [1.0KHZ]/[LVL 00]/[Q1.25])
[TREBLE] Frequency : [10.0KHZ]/[12.5KHZ]/[15.0KHZ]/[17.5KHZ]
Level : [LVL–06] to [LVL+06]
Q : [Q FIX]
(Default : [10.0KHZ]/[LVL 00]/[Q FIX])
level. ; [OFF]: Cancels.
[LEVEL 01]/[LEVEL 02]: Boosts low or high frequencies to produce a well-
balanced sound at low volume. ; [OFF]: Cancels.
[SPK-OUT]*2 [SUB.W 00] to [SUB.W +06] ([SUB.W +03]): Adjusts the
output level of the subwoofer connected via speaker lead.
(Page 19)
[PRE-OUT]*3 [SUB.W –08] to [SUB.W +08] ([SUB.W 00]): Adjusts
the output level of the subwoofer connected to the lineout
terminals (REAR/SW) through an external amplifier.
(Page 19)
11
ENGLISH