HIKOKI CR 18DBLW4 Instrucciones De Manejo página 8

English
○ When the pilot lamp fl ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○ Since the built-in micro computer takes about 3
seconds to confi rm that the battery being charged with
charger is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery
is reinserted within 3 seconds, the battery may not be
properly charged.
○ Check the voltage of the in-car power source when
the pilot lamp fl ickers in green (every 0.2 seconds)
continuously. (UC18YML2)
If the voltage is 12 V or lower, it indicates that the car
battery has weakened and cannot be charged.
○ If the pilot lamp does not blink in red (every second) even
though the charger cord or cigarette lighter connecting
plug is connected to the power, it indicates that the
protection circuit of the charger may be activated.
Remove the cord or plug from the power and then connect
it again after 30 seconds or so. If this does not cause the
pilot lamp to blink in red (every second), please take the
charger to the HiKOKI Authorized Service Center.
MOUNTING AND OPERATION
Action
Removing and inserting the
battery
Charging
Switch Operation
Remaining battery indicator
Adjusting operating speed
Mounting the blade
Dismounting the blade
*2
How to use the hook *3
Select a saw blade of the
appropriate length
Fasten a workpiece fi rmly
Adjusting the base
Plunge cutting (for wood)
Selecting accessories
*1 Adjusting operating speed
CAUTION
Select mode while the trigger switch is released. Failure
to do so could result in malfunction.
Once you install the battery and switch on the power, you
can change modes with each press of the mode selector
switch.
● Speed change mode allows the number of maximum
strokes to be switched between 3 levels: low speed,
medium speed and high speed.
With speed change mode, the set number of maximum
strokes will be maintained even if there is a change in
load.
● With auto mode, electricity consumption and noise can
be suppressed by lowering the number of maximum
strokes during no-load motor operation.
Auto mode automatically increases the number of
revolutions when the load becomes heavier during
operation. When the load becomes lighter, the number
of revolutions is automatically reduced.
Figure Page
2
3
4
5
6
*1
7
8
9
10
11
12
13
―
Operating speed
Mode
Transmisson
Mode
Auto Mode
CAUTION
Do not cut stainless steel in Auto Mode.
*2 Dismounting the blade
CAUTION
Never touch the saw blade immediately after use. The
metal is hot and can easily burn your skin.
(1) After pivoting the lever, point the blade downward. The
blade should fall out on its own. If the blade fails to fall
out, pull it out by hand.
WHEN THE BLADE IS BROKEN
Even when the saw blade is broken and remains inside
the small slit of the blade holder, it should fall out when
the lever is pivoted and the blade is pointed downward.
If the blade fails to fall out on its own, take it out by using
the procedures described below.
(1) If a part of the broken saw blade is sticking out of the
small slit of the blade holder, pull out the protruding part
213
and take the blade out.
(2) If the broken saw blade is hidden inside the small slit,
213
hook the broken blade using a tip of another saw blade
and take it out. (Fig. 8)
214
214
*3 How to use the Hook
214
The hook can be used to hang up the unit
temporarilyduring operations (Fig. 9).
214
CAUTION
214
The hook should never be used to hang the unit on your
person.
215
When using the hook, check to make sure that the main
215 unit will not slip and fall, or become unstable by the wind,
etc.
215 Never hang the unit from your belt or trousers as this
could cause accidents.
215
215
LED LIGHT WARNING SIGNALS
217
(Fig. 16)
This product features functions that are designed to protect
the tool itself as well as the battery. While the switch is
pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in
Table 3. When any of the safeguard functions are triggered,
immediately remove your fi nger from the switch and follow
the instructions described under corrective action.
8
Statuse Operating speed
Low 0 – 1600 min
-1
Medium 0 – 2300 min
-1
High 0 – 2500 min -1
0 – 1600 min -1
A 2500 min (When the
-1
load becomes heavier)
Fig. 16