Publicidad
Idiomas disponibles
Idiomas disponibles
GETTING TO KNOW YOUR CLEANER
A.
Cleaner main body
B.
Carry handle
C.
Dust Container
D.
Dust Container handle and latch
E.
On/Off Button
F.
Cord Rewind Button
G.
Filter Door
H.
Filter Door latch
I.
Pre-Motor Filter Pack
J.
Exhaust Filter Grid
K.
Exhaust Filter
L.
Parking Slot
M.
Handle
N.
Suction Control
O.
Telescopic Tube
P.
Telescopic Tube Adjuster
Q.
Carpet and Floor nozzle(GP)**
Q1. Carpet Nozzle (CA)**
Q2. Hard Floor Nozzle (HF)**
R.
Surface Selector**
S.
Hose
T1.
Crevice Tool
T2.
Dusting Brush
U.
Pet Hair Remover Mini Turbo Nozzle*
V..
Allergen Remover Mini Turbo Nozzle*
W.
Grand Turbo Nozzle*
X.
Parquet Nozzle*
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
Connect the hose to the cleaner main body. [2]
1.
2.
Connect the tube upper end to the navigator handle [3].
3.
Connect the tube lower end to the carpet and floor nozzle. [4]
*Certain Models Only
** Certain models only, nozzles may vary according to model
USING YOUR CLEANER
1.
Extract power cord and plug it into the power supply. Do not pull the cord beyond the
red marker. [5]
2.
Adjust the telescopic tube to the desired height by holding the handle and moving the
central hand grip up or down. [6]
Select the type of surface to be cleaned by pressing the pedal in the nozzle. [7]
3.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4.
Switch the cleaner on by pressing the On/Off Button on the cleaner main body. [8]
5.
Adjust the suction by sliding the suction regulator to the desired level. [9]
6.
Switch off at the end of use by pressing the On/Off Button. Unplug and press the cord
rewind button to wind the power cord back into the cleaner. [10]
7.
To store your cleaner adjust telescopic tube to the lowest height setting and park the
nozzle in the park position on the cleaner main body. [11]
ACCESSORIES
To obtain the best performance and efficiency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams by the
letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended for oc-
casional use only.
Please see the model specification on the packaging label for inclusion of accessories to
individual models. All accessories can be purchased separately from Hoover. (See Hoover
Spares and Consumable section).
All accessories can be fitted to the end of the hose or the end of the telescopic tube.
Crevice Tool – For corners and hard to reach areas. [12]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To extend the
brushes push the button on the body of the tool. [13]
Parquet Nozzle* – For parquet floors and other delicate floors. [1X]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1W]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs
removal. [1U]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas, particularly suitable for allergen
removal. [1V]
2
*Certain Models Only
** Certain models only, nozzles may vary according to model
GB
Publicidad
